News

A Contour-Cut Sticker Sheet: From the File With Marks to Packing
Step by step: marks and contours in the file, gaps of 3 mm or more, 100 % print on matte PP film, cold laminate only over the sticker block, kiss cut on the MC330 camera plotter (45° knife, 0.25 mm offset, force from a test), weeding, trimming and packing.
Why a sublimation print looks pale on paper and bright after pressing
A diagram of the dye’s path from a pale sheet to a bright T-shirt or mug: what sits on the paper, what the press does at 180–200 °C, what you can judge on the sheet before pressing, and why colour is corrected with a profile and a test item, not in the design.
Armed Forces Day gifts: what to print and when to stop taking orders
What to print for soldiers and veterans for Armed Forces Day on 6 December: four products from MyPrint blanks with prices and settings, what to get from the client, and a calendar from 10 November with the last days to accept and ship orders.
White edges on a photo slate: small artwork or no contact?
A straight white border and unprinted chips need different fixes. Check the image bleed, then see whether the transfer touches the recessed edge.
Calendar pages catch on the hanger: how to make the clearance notch
Each page needs room to pass the hanger's central bend. See how to align the notch through every calendar layer with the gap between the two wire sections.
Heat press temperature and time for 20 MyPrint sublimation blanks
White mug: 200 °C for 180 s; glossy metal: 180–200 °C for 60–90 s; T-shirt: 190–200 °C for 40–60 s. 17 more blanks in three tables by press type, with pressure and the source of each figure.
What it costs to make a logo mug: 1, 10 and 100 pieces
Mug, paper, ink, heat tape, box, electricity, test mug and defects — every line with MyPrint product-page prices. Materials stay at 65–70 UAH at any run size, while the time per mug falls from 25 to 4.4 minutes.
Mug Print Shifted or Tilted: How to Wrap and Tape the Paper Straight
A table for a tilted, spiralled or shifted print and the arc on a latte mug: cause, check, what to change. Step by step: cutting, wrapping on the table, 4 pieces of heat tape, the handle in the middle of the heater, an arc template for latte mugs.
Mug press for your volume: 10, 50 or 150 mugs a day
Mug press cycle arithmetic and a comparison of one, two and five heaters and a multifunction press: what to buy for 10, 50 and 150 mugs a day and which heaters latte mugs and tumblers need.
Branded Thermo Mug: Cost and Price for 1, 10 and 50 Pieces
The cost of a branded thermo mug worked out on MyPrint prices as of October 2026: blank, paper, ink, heat tape, minutes, spoilage and the press share. A table for 1, 10 and 50 pieces, the price with a markup and a formula for your own prices.
What to Print for New Year: 7 Products and a Calendar to 31 December
Seven products from MyPrint blanks for the New Year season: the press for each, what to offer families, small businesses and companies, and a calendar from October to 31 December with the last shipping dates.
What to Charge for Laminating A4 and A3: Cost per Sheet and Price
The cost of laminating an A6–A3 sheet in 80, 125 and 150 µm film for a copy shop: the formula, a table for 1, 10 and 50 sheets, an example price list and the price below which a run stops paying.
A cap with a logo on a heat press: step by step from artwork to packing
A step-by-step cap press project: logo size for the heating element, mirrored print, cap on the form, 190 °C and 50 seconds, checking and packing. Cotton caps get film instead.
20 A5 notebooks on metal wire: from file to packed batch
Step by step: layout and printing, cutting to A5, choosing the wire by block thickness, punching 20 sheets at a time, closing and packing, with the time for a batch of 20 and the MyPrint consumables.
Comb, Metal Wire or Glue: How to Bind a Report, a Menu and a Catalogue
Plastic comb, metal wire, plastic coil and hot-melt glue for six documents: how many sheets each holds, whether it lies flat, the cost per copy and the time for 1, 20 and 200 copies.
Heat Press Care Table: What to Clean, Check and Replace
One table to keep by the press: what to do daily, weekly, monthly and every few months on a flat and a mug heat press, how to clean the platen without harming the coating, and which signs mean it is time to replace the Teflon sheet, silicone pad, heater or handle.
A first sublimation kit: what is in the box and how many items a day
What MyPrint's sublimation starter kit holds, what it can and cannot do, how many mugs and flat items it makes an hour, which three products to sell first and what the start costs with the first stock of blanks.
Polyester or Two-Layer: Which T-Shirt to Use for Sublimation
Polyester 170 g/m² for events and teams, two-layer 200 g/m² for staff uniforms, merch and kids. How they differ, what they cost and when you need DTF.
How to Make a Foil Gift Certificate on a Laminator
Step by step: a 210 × 99 mm layout with three certificates per A4 sheet, printing, foil at 130–150 °C on a roll laminator, the test sheet and what to change, guillotine cutting, creasing and packing.
Mouse Pad with a Photo or Logo: From File to a Batch of 10
Step by step: choosing the pad and the layout size, mirrored printing, heat tape, 190 °C and 55 s with a 200 °C ceiling for the rubber base, peeling, cooling, checking the first pad and a batch of 10 in 25–35 minutes.
What circle to cut for a 25–58 mm button badge and how much shows
A 25 mm badge needs a 35 mm circle, a 44 mm badge 54 mm and a 58 mm badge 70 mm. One table for five sizes: what shows on the front, where text goes, how much fits, and which die, cutter and blanks to use.
UV DTF Sticker on a Thermo Bottle: From Layout to 10 Finished Bottles
Step by step: measuring the bottle, a 100 % scale layout, printing with film B lamination, cutting, degreasing, squeegee application, peeling films A and B, palm pressing and a care card. Plus the time for a run of 10 bottles and when sublimation is the better choice.
How a thermo mug is built and why it is pressed differently from ceramic
A thermo mug in cross-section: thin steel, vacuum, coating. Why it presses faster than ceramic, which heater fits its diameter, what to remove before pressing and how to wash the finished piece.
UV DTF Stays on the Film: How to Transfer Fine Details
A small letter lifts with the film? See how to press it back into place, peel the film and recognise a transfer that needs replacing.
Pale band at the bottom of a sublimated mug: the mug or the press?
The thick base soaks up heat, and a tapered mug pulls away from the heater. Put the next mug into the press the other way round, and the band will show what to fix: the mug preparation or the press.
How a Badge Machine Works: What Happens in Its Two Strokes
How a badge machine assembles a badge without glue: the first stroke lifts the shell with the insert and film into the upper die, the second rolls the shell's skirt over the back. Why every part must match the die, what wears, and a defect → stage table.
White Patches on a Sublimated Mug: What Their Position Tells You
A white patch on a mug is where the dye from the paper did not reach. How to find the cause from the used sheet and the patch’s position: the wrap by the handle, pressure, the heater, moisture, dust or the coating, and how to check the change with one mug.
Cut vinyl lettering: how to transfer a word and remove the transfer film
Transfer film first picks up the faces of the letters, then needs to release them after application. See the layers, peeling direction and what to do when part of a word stays on the wrong layer.
Laminating Film Thickness: A Table from Menus to Badges
A copy-shop table: 80, 100, 125 or 150 µm film for each item, how to match the pack number with the laminator, A5–A3 formats, gloss or matte, and when cold film replaces a hot pouch.
Why an Ordinary Mug Won’t Take Sublimation Ink and What the Coating Does
A sublimation coating is a thin polymer layer on the blank: in the press the dye turns to vapour and enters it, and after cooling it stays inside. A layer diagram, a table of coating faults, the limits of sprays and a check for a new batch.
QR codes on labels: calculating the size including the white margin
The same 20 × 20 mm area can hold QR codes with very different detail sizes. Calculate the module, symbol and margin, then decide what to change before a print run.
Photos behind glass: matte or glossy paper, and why use a mat?
Matte paper does not remove reflections from front glass. We explain two light paths, choices for a particular room, and framing with space between print and glass.
A white line on a card fold: how creasing helps
A crease prepares a hinge region before folding. See which way to fold it and how a trial of two paper orientations helps you choose the card imposition.
3:1 or 2:1 wire binding: hole pitch and complete notebook thickness
Match the wire pitch to the holes first, then measure the whole block including covers. See how 3:1 differs from 2:1 and why 120 pages can produce different thicknesses.
Laminated cards: cut before or after laminating?
For a sealed card edge, trim the paper before laminating and the film after cooling, retaining a continuous border. Edge cross-sections and an A4 example show why.
Embroidery on terry: why water-soluble film goes on top
Topping film holds down terry loops; backing supports the fabric underneath. See the layer order and a comparison that separates pile problems from puckering and overly fine lettering.
A gold logo on paper: toner foil or hot-stamping foil?
The same gold shine can come from different processes. These diagrams explain when you need toner-reactive foil, when you need a die, and why foil coverage matters to the artwork.
White or silver sublimation metal: what happens to white in your artwork
White in a sublimation print comes from the blank's base. See what undyed areas reveal on white and silver metal, and how two different orders call for different materials.
44 mm badge, 54 mm insert: what wraps around the edge
The badge and its paper insert have different diameters. See MyPrint pc44 geometry, a ruler check for print scale, and a worked rectangular A4 layout with explicit assumptions.
Heat press 38 × 38 or 40 × 50: what fits in one pressing
How much of the plate takes the print, what fits on 38 × 38 and 40 × 50, from a kids' T-shirt to A3, a tote bag and two puzzles at once, and which MyPrint press to choose: clamshell, swing-away or drawer.
Why the design still shows on a cold colour-changing mug
A design does not always disappear completely on a cold magic mug. Learn to tell a faint silhouette from coating damage and check a blank before a print run.
How to Wash a Printed T-Shirt: Care Card for Sublimation, DTF and Film
One care card for three technologies: 48 hours before the first wash, inside out, 30 °C without bleach or softener, air drying, ironing on low heat from the reverse side. Tables with makers' limits, why they differ, and questions for a customer who complains about the print.
A pale band next to a seam after sublimation: position the pillowcase correctly
Seams and zippers can prevent even pressure. Learn how to position a polyester pillowcase so the whole design transfers onto a flat area.
Laminated Café Menu: From File to a Set for 10 Tables
Step by step: which paper for which pouch, why to keep 3 mm of sealed film, how to make a film hinge for the folded menu and wire-bound pages with holes in film only, R3 corners and a time table for 80 pouches.
Sublimation is too dark after pressing even with the ICC: what should not change first?
Check nozzles, the colour profile, blank and heat press in sequence without arbitrarily brightening the artwork or jumping to a diagnosis.
The first contour is accurate, then drift grows: what should you check?
How to distinguish constant contour displacement from increasing scale, feed or registration errors, and what to check before resuming production.
When is an eco-solvent print actually ready for lamination?
There is no universal drying time: lamination begins only after the current conditions for the exact ink, print media, and laminate combination have been met.
A Water Bottle with a Name: From File to a Run of 20
Step by step: a template from the bottle’s circumference, 20 names from a list without retyping, mirrored printing, a tight wrap with heat tape, a test bottle at 180 °C and 60 s, checks, packing and a time table for a run of 20.
White ink runs on DTF film: what to change after replacing the roll
White prints cleanly on its own but runs over colour. A small comparison can help you check the new film and white ink loading before starting the production run.
Numbers and Surnames on Team Kit with Heat-Transfer Film: 15 Shirts
Step by step for a workshop with a plotter and a flat press: number and surname sizes by the regulations and in practice, a mirrored layout on 0.5 m film, a test cut, weeding, marking from the collar, pressing at 150 °C for 10 s, cold peel, a care note, and the time and film for 15 kits.
DTF film hits the printhead: how to stop lifting and smears
A raised edge of DTF film can touch the printhead and leave a wet smear. Learn how to flatten the media and check the result before a production run.
Rounded corners and horns: how to check blade offset compensation
The film cuts through, but the lettering has rounded corners or protrusions? Learn how blade offset works and assess the same test after changing one setting.
How to Leave a Sublimation Printer for a Holiday Without Drying the Head
What to do with a sublimation printer when there are no orders: a weekly nozzle check, preparing for a holiday, switching off without drying the head, and a decision tree after the break: how many cleanings, when to pause for 12 hours and when to call service.
What to Print for 1 September and When to Stop Taking Orders
A 1 September plan for a print shop: what to print for a class and as a teacher gift, on which press, how long a named run for 30 children takes, until which day to take orders and when to ship by Nova Poshta so parcels reach the branches on 28 August.
DTF film lifts the print during peeling: what should you do?
How to check DTF film release on a control sample without confusing clean carrier removal with complete print-quality acceptance.
Independence Day Without the Rush: Six Items and the Last Order Days
Six items for 24 August for a company, community, school or one person: blanks and settings, a run on one press, what the law says about the coat of arms and the flag, and a calendar with the last days to take orders and hand over parcels.
Black sublimation ink bleeds on polyester: what to change in printing
A blurred black edge on polyester: use the paper print to decide what to change — driver density or pre-pressing and paper removal.
Small HTV letters lift during weeding: how to keep them in place
A sticky carrier, separate weeding boxes around each line and the right orientation for a loose dot: keep small HTV lettering intact before pressing.
Tear-off coupons: how cuts and ties work
What keeps a detachable coupon attached, why tooth count alone is not enough, and how to distinguish incomplete cuts from unsuitable tie geometry.
How to support the whole print inside a sewn tote
Seams and handles can interfere with pressing even when the design sits on flat fabric. Compare three support methods and calculate the support footprint inside a sewn bag.
Banding in a sublimation print: what to check before heat transfer
How to rule out a file defect, nozzle dropouts and a paper-feed error without wasting ink on unnecessary cleaning cycles.
EVA or PUR for edge banding: what changes in the workshop
EVA can be remelted; reactive PUR also cures through a reaction with moisture after cooling. Compare the demands on the machine, daily workflow and finished bond.
Stickers curl after cutting: how to remove them from the mat
The cut is clean, but the sticker curls as you lift it? Learn how to peel the mat away, keep the backing intact and choose the right grip.
Adhesive halos around heat transfer vinyl: how to get a clean edge
Clear adhesive around letters comes from excessive pressure or heat. How to set medium pressure and make a sample with a clean edge.
Black scuffs on the edge of photo paper: what to change
The photo is almost finished when its last edge emerges with a black scuff. Check sheet curl, margins and head clearance before wasting another pack.
Cutter leaves marks on the stack edge: when to replace the blade
A track on the cut face can come from a nick in the blade, paper shifting under the clamp or a worn cutting stick. Learn to tell them apart and decide when to replace the blade.
Ragged holes in clear binding covers: how to get a clean punch
Paper punches cleanly, but plastic tabs hang from your clear cover? See how to assemble a trial stack and when to check the cover material or punching dies.
Heat press and infrared thermometer disagree: should you turn up the heat?
A low infrared reading does not prove that the platen is too cold. Check what the instrument is measuring before raising the temperature or ordering a spare part.
How to Store Inks, Films, and Papers in a Small Print Shop
One stock-flow system for different consumables without an invented shared climate: SKU cards, four storage zones, lot identity, FEFO/FIFO, weekly inspection, and quarantine.
Will a UV DTF Transfer Stick? A Surface-Test Protocol Before Production
A bounded compatibility protocol for one product and lot: how to prepare a test coupon, what to observe, when to retest, and which signs stop production.
A Technical Brief for Corporate Merch: What to Collect Before Quoting
A brief structure that turns “we need merch” into a stable quoting scope: products and sizes, decoration, samples, kit contents, addresses, dates, and controlled assumptions.
Plotter Test Cuts: Setting Blade, Force, and Speed Without Wasting Film
A repeatable protocol for a new film–blade–holder combination: what to check first, how to read the test mark, which single control to change, and when not to run the roll.
Ghosting during sublimation: find the moment of movement
A faint directional copy does not arise at every stage. Check the transfer before pressing, locate movement in the cycle and correct one confirmed operation.
Uneven heat-press contact: check the platen without disassembly
Two separate maps distinguish weak platen contact from a cold zone. The method localises a fault without an invented tolerance, disassembly or whole-recipe compensation.
Paper, self-adhesive film or banner: choose the carrier by installation
The installation method quickly removes two of three carriers. Identify what holds the graphic, then check the surface, finish and exact material documentation.
Artwork preflight before printing: accept, repair or return the file
A sequential preflight for one defined production output, from geometry and live objects to special-layer recognition in the RIP and a clear file decision.
Photo Products & Photo Printing on Souvenirs: Technologies, Product Range & Business Model
Photo product market research: photo mugs, pillows, magnets, puzzles and crystals. Sublimation and UV printing technologies, full product range with costs and business model. ---
How to store finished UV DTF transfers before application
Keep finished UV DTF transfers flat, between films A and B and out of sunlight. See how to pack stock for shipping and which damaged designs to reprint.
Bump or dent on a button badge: what to check
A particle under the film and a dent in the metal shell need different remedies. See what to inspect, how to clean the dies and how to check the next badge.
Plastic coil unwinding from a notebook: why both ends need crimping
A neat cut only removes surplus coil. See how an inward bend obstructs unwinding, why both ends need finishing, and what to check on the completed notebook.
Textile Accessory Printing: Scarves, Bandanas & Ties — Technologies & Business Potential
Research on textile accessory printing: scarves, bandanas, ties, headbands. Sublimation and DTF, fabric selection, production costs and profitable niches from fashion to corporate merch. ---
Badge artwork turned sideways: how to align it with the pin
Centring a circular insert does not set the artwork's angle to the pin. Four reference marks help you find where to aim the next design's top and check it on the finished badge.
How large can you print a photo? Calculate from its pixels
One 2400 × 1600 pixel file gives 254 PPI at 24 × 16 cm and 203.2 PPI at 30 × 20 cm. Calculate from the printed image size and choose an output that fits the job's requirement.
Shoe Printing: Sneaker, Canvas & Slip-on Customization Technologies
Research on shoe printing: DTF, UV DTF and sublimation on sneakers, canvas shoes and slip-ons. Compatible materials, customization costs, durability tests and business potential. ---
125 µm pouches and thick paper: can your laminator handle both?
A pouch can match a laminator's supported marking yet exceed its thickness limit once paper is added. We explain the three layers with a hypothetical 0.55 mm example.
HoReCa Workwear Printing: Branding Technologies for Aprons, Polos & Uniforms
Research on HoReCa workwear branding: aprons, polos, chef coats. DTF printing vs embroidery, industrial wash durability, costs. B2B model with recurring orders. ---
Embroidery without soaking: when to choose heat-removable film
Heat-removable film offers a dry finish when the entire item can tolerate the required treatment. Compare two examples and follow the removal of the particles.
Hot-melt carton flaps: when to join them and when to let go
The glue has hardened, but the flap lifts? Separate the delay before joining from holding afterwards. A four-box example shows where to start the clock and how to test an avoidable delay.
Event Promo Product Printing: Complete Guide to Products, Equipment & Business Model
Guide to event promo product printing: pins, stickers, tote bags, t-shirts, badges. Cost per product, equipment needed and financial model. From conferences to festivals. ---
White edges on UV DTF: how to remove the halo around a design
An even white outline and white protruding on just one side need different fixes. Learn what to check in the artwork and how to adjust the underbase without losing fine strokes.
Crop marks cut off? Finish business cards using the backgauge
Trimming the margins removes the marks, but the dimensions remain. See how to finish six business cards from one reference edge while removing every gutter.
Children's Clothing Printing: Material Safety, Certification & Printing Technologies
Research on safe children's clothing printing: OEKO-TEX and CPSIA standards, safe DTF and sublimation inks, durability and toxicity tests. Niche with margins up to 500%. ---
How to replace a page in a plastic-comb catalogue
Has one page of a finished catalogue changed? Replace the whole leaf, including its reverse. Learn how to check the holes, open the comb with a binder and reassemble the document.
A ticket to keep: copy first, laminate afterwards
For a keepsake card, first save a readable photograph or scan of the ticket. Print a separate reproduction, try protective film on a spare print and keep the original separately.
Heat Press Comparison: Manual, Pneumatic & Automatic — Complete Test & Buyer's Guide
Complete heat press comparison for DTF and sublimation: manual flatbed, pneumatic and automatic. Heat uniformity, pressure and productivity tests. Recommendations by production volume. ---
Shiny hoop ring after embroidery: how to remove hoop burn
Water and steam for cotton, care with polyester, a backing frame under the hoop and a towel floated on hooped backing: remove hoop burn and avoid the next one.
Silvery specks under cold laminate: how to reduce silvering
Does a dark laminated print look sprinkled with salt? Most often it is air between the adhesive and the print. Here is how to make a sample and distinguish silvering from dust and large bubbles.
Sportswear Printing: Technologies, Fabrics & Durability Under Physical Stress
Sportswear printing research: DTF and sublimation. Sweat, stretch and 100-wash durability tests. Recommendations for soccer clubs, fitness studios and sports teams. ---
Calender vs Flat Heat Press: Which One to Choose
Calender heat press — for roll materials and high-volume fabric production. Flat heat press — for t-shirts, mugs, caps. Comparison and recommendations.
Badge Making Equipment: Complete Guide
Complete set for badge production: press machine, dies, materials. Prices, badge types, cost per unit, and business profitability in Ukraine.
DTF Printer Comparison: XP600, I1600 & I3200 Printheads — Complete Analysis
Detailed DTF printer comparison by printhead type: XP600, Epson I1600 and I3200. Speed, quality, lifespan and maintenance cost tests. Recommendations for different budgets and volumes. ---
Why DTF Print Cracks After Washing: 5 Causes and Solutions
DTF print cracking after washing? Learn the 5 main causes and how to fix them. Pressing parameters table for cotton, polyester, and blended fabrics.
Perfect-bound booklets: why the spine is milled
A neat spine does not show whether glue can reach the inner leaves. Clear diagrams explain preparation for folded sections and separate loose leaves.
UV DTF vs UV Printing: Difference and Applications
UV DTF — stickers on any surface without a heat press. UV printer — direct printing on wood, metal, glass. Comparison, applications, prices.
Bottom sheets not cutting through: when to check the cutting stick
The top of the stack separates, but the bottom sheet stays joined? Understand the support beneath the blade and why the check must span the full cutting width.
How to Choose a Sublimation Printer for Mugs and Souvenirs
Which printer is needed for sublimation on mugs? Comparison of Epson L800, L805, L1800. Equipment, costs, common mistakes, and cost per mug.
Adhesive film for embroidered patches: why bonding takes two stages
The adhesive must bond both to the back of the patch and to the fabric of the item. Follow a paper-backed film example to see when the surplus and protective paper leave the assembly.
Printing on Tote Bags & Eco Bags: Complete Guide to Technologies, Equipment & Profitability
Complete research on tote bag and eco bag printing technologies: DTF, sublimation and screen printing. Cost comparison, wash durability, equipment and materials selection. Tote bag business financial model. ---
DTF Print Cost: How Much Does 1 A4 Print Cost
How much does 1 A4 print cost on a DTF printer? Detailed breakdown: film, ink, powder, depreciation. Real 2026 figures for business in Ukraine.
DTF Printing in 2025-2026: Technology, Advantages and Business Opportunities
DTF (Direct to Film) — технологія друку на будь-якій тканині через плівку та термопрес. Стартовий комплект від 167 000 грн, собівартість 1 принту A4 — 25-30 грн, окупність 3-8 місяців.
Cap and Hat Printing: Technologies, Equipment, Lifehacks
Mastering all cap printing technologies: DTF, sublimation, embroidery, and screen printing. Detailed equipment overview, working with different materials, popular 2026 designs, and professional lifehacks for quality results.
Epson i3200 vs XP600 for DTF Printing: Detailed Comparison
Epson i3200 vs XP600 for DTF printing: comparison of resolution, speed, ink consumption, and maintenance costs. Which is better for startup and business?
Sublimation Gifts: TOP 15 Business Ideas
Sublimation gifts: TOP 15 ideas with equipment and blanks from My Print.
Custom Badges and Keychains: Equipment, Calculation, Niche
Building a badge and keychain production business: from choosing a badge machine to finding profitable niches. Detailed calculation of investments, costs, and margins. Practical advice on production organization and service promotion.
Water-soluble thread for appliqué: when to remove the basting
Water-soluble thread holds pieces only until they are permanently sewn on. See which stitches water removes, what stays on the fabric and when the cushion cover is ready to wet.
How to Choose a Heat Press for T-Shirts: 5 Key Criteria
How to choose a heat press for t-shirts: plate size, pressure uniformity, control type, manual vs pneumatic, warranty. Prices and recommendations.
DTF Printing on Workwear and Uniforms: B2B Opportunities
DTF printing on workwear: technology, benefits, costs for B2B.
Mug Printing: Sublimation, Decal, UV — Which to Choose?
Choosing a mug printing technology for business or hobby? We analyze all popular methods: sublimation, decal transfer, UV DTF, and screen printing. We compare cost per unit, wash resistance, photo print quality, and required equipment for each method.
Sublimation Inks: Complete Buying and Usage Guide
Sublimation inks — how to choose, types, printer compatibility. Complete guide.
How to Start a DTF Printing Business: Equipment and Costs
How to start a DTF printing business in Ukraine: equipment list, real prices, budget from 169,000 UAH and payback period. Complete startup guide.
Lace without fabric: choosing a file for a bookmark
Water-soluble support holds embroidery only temporarily. A bookmark with rings shows what must hold the lace together once that support is removed.
DTF vs Sublimation: What to Choose for Business in 2026
DTF or sublimation — comparison of printing technologies for business: prices, equipment, costs. Which technology is more profitable in 2026.
Print Shop Ventilation and Safety: Chemistry, Standards, Solutions
Comprehensive guide to DTF print shop safety and ventilation. Detailed analysis of DTF powder and ink toxicity, ventilation system requirements, air filtration methods, fire safety and compliance with Ukrainian workplace safety standards with practical safety checklist.
Photo looks darker after laminating: should you lighten the file?
Does your photo look darker under laminate? Three identical prints help you choose gloss or matte and decide when the printing actually needs adjusting.
Stickers peel off bottles after lamination: what to change
A protective film makes a sticker stiffer, so it springs back on a bottle's curve. Two samples show what to change: the laminate, the corners or the adhesive.
Mug Printing: Sublimation as Business
Mug printing with sublimation: equipment, blanks, cost and profit.
New button badge blanks will not fit the die: what to check
Matching sizes do not guarantee compatibility: MyPrint blanks of one size come in Premium and Standart classes. How to check the class and dry-fit the parts without ruining a new batch.
How to Build a Garage Print Shop: From Zero to Production in 30 Days
Practical guide to creating a full-fledged print shop in a garage in 30 days. Detailed plan for space preparation, electrical work, ventilation installation, equipment placement and first order launch with budget calculation and timeline.
Plotter cannot read registration marks after lamination: what to do
Glossy film over the marks blinds the plotter. How to check the cause and laminate only the stickers: 3 mm past the cut lines, 1 cm short of the marks.
Fuzzy patch edges: how to stitch a clean border
Fuzz around a patch can come from its backing or the fabric itself. See how to cut the blank before edging it, then stitch the border on water-soluble film.
Heat transfer vinyl cracks on knitwear: what to change
The edges hold, but cracks open inside the design? Check the film, the press settings and the placement. Learn to tell a tear from lifting and test a sample before the run.
UV DTF Stickers for Products: A New Business Niche
UV DTF stickers: what they are, business ideas and equipment. New niche from My Print.
Print Production Automation: From Manual to Streamlined Operations
Comprehensive review of print production automation: from simple manual operations to fully automated production lines. Analysis of conveyor heat presses, automatic shakers, RIP queue management systems and ROI calculation for different automation levels.
Labels for tapered containers: why rectangles wrinkle
A conical band has different top and bottom circumferences, so a broad label needs a curved development. Follow three measurements, construct the outline and check a paper dummy before printing adhesive labels.
DTF Powder (Adhesive): How to Choose and Use Properly
DTF powder (hot melt adhesive) is an essential part of DTF technology. We cover types, particle sizes, selection criteria, application rules, and storage. Everything for quality DTF prints.
Duplex printing: long-edge or short-edge flip?
A portrait menu turned sideways needs a long-edge flip; a landscape menu turned the same way needs a short-edge flip. Four diagrams and a simple probe explain how to keep the back upright.
Printing on Dark and Black Textiles: Technologies for Perfect Results
Comprehensive overview of modern dark and black textile printing technologies. Detailed comparison of DTF, DTG, HTV and screen printing, practical white base layer tips, secrets for achieving vibrant colors on dark fabrics, and analysis of common production mistakes.
Bubbles under UV DTF on glass: how to apply a smooth decal
Prevent bubbles while the decal still has an open edge. See how to move the squeegee, give air an escape route and remove a bubble that has already formed.
Mug cracked in the heat press: how to protect the next one
A cracked mug calls for a fit and pressure check, or a look at cooling if it cracked after removal. Prepare the next blank without wasting more mugs.
Shrink-film keychains: how to calculate the starting dimensions
Divide the desired finished dimensions by the measured shrink ratios. We work through both directions, a 27 × 18 mm example and the attachment hole.
Fabrics and Materials for Printing: Scientific Compatibility Guide
Fabric choice is a key factor in successful heat printing. Different fibers react differently to temperature, humidity, and adhesives. This scientific guide reveals compatibility principles of polyester, cotton, blended fabrics with DTF, sublimation, and heat transfer, providing a practical matrix for choosing optimal technology-material combinations.
Cutting Plotter: How to Choose for Sticker and Label Business
How to choose a cutting plotter for sticker business? Types, features, business ideas.
How to hide a notebook’s wire join behind the back cover
The wire join can sit between the last sheet and the back cover. See how to arrange the covers before binding and check the finished notebook.
Oily DTF transfers: what to change in curing
Oily residue after curing: compare two prints and calculate how long the film spends in the heated zone.
Pages falling out of wire binding: how to adjust the closer
An open loop lets sheets escape; over-closing flattens the wire. See how to set the closer and when to use a fresh wire element.
Badge Making: Equipment, Materials and Business Model
How to start badge making: equipment, blanks, business model, ROI.
DTF White Ink: Complete Guide to the Most Problematic Component
White ink is the most challenging component of DTF printing due to high concentration of TiO2 pigment, prone to sedimentation and nozzle clogging. This guide reveals technical aspects of working with white ink, circulation systems, maintenance schedules, and methods for troubleshooting the most common problems to ensure stable DTF printer operation.
Why glass clouds over a fresh photo: drying prints before framing
The photo no longer smudges, yet the glass clouds after framing. Here is how to dry the print and check whether the haze is on the glass or in the image itself.
Cutter clamp marks on business cards: how to protect the stack
A band on the top business cards after cutting may be a mark left by the clamp. Learn how to check the cause and protect the print while keeping the cut accurate.
Two HTV colours: cut-out spaces instead of a solid base layer
Place the second colour in a cut-out space so both films bond to the fabric. A circular emblem shows how to subtract shapes and leave an intentional ring of fabric.
Sublimation on Fabrics: Which Materials Work and Why
Sublimation on fabrics: which materials work, why polyester, cotton alternatives.
UV Technologies in Printing: From Photopolymers to UV DTF and UV LED
Unveiling the world of UV printing technologies: from photopolymerization chemistry to modern UV DTF printers. Learn how UV LED lamps work, why they're replacing mercury lamps, and what advantages UV curing offers for different applications.
Sublimation bled onto the back of a shirt: where to put protective paper
Paper on top protects the platen; paper inside protects the back of the shirt. Where to put the paper, what the colour on it means and how to print the second side.
Two-layer engraving plastic: remove the letters or the background?
The engraving colour is already inside the two-layer stock. Compare removing the letters with removing the background, then choose the layers for your sign.
Heat Transfer Vinyl (HTV): Types, Application and Tips
HTV film: types, workflow and tips from My Print.
Heat Press Physics: Why Degrees, Seconds and Pressure Determine Everything
Unveiling the scientific principles of heat press operation: how temperature activates adhesive, why time affects durability, and how pressure ensures even transfer. Practical parameter tables for all heat transfer technologies.
Paper curls after roll lamination: what to adjust
The direction of the curl shows which roll is too tight. See how to balance the tension and what to do when only one side is laminated.
DTF Film: Types, How to Choose and What to Look For
Complete guide to DTF film: types by surface and peeling method, selection criteria, storage rules, and troubleshooting. Everything you need to know for quality DTF printing.
Future of Printing Business 2025-2030: Technologies, Trends, Predictions
Exploring the future of printing industry: revolutionary nanotechnologies, AR/VR integration, direct-to-fabric evolution, 3D printing crossover. Analyzing sustainability trends, market consolidation and key skills for success in the future printing business.
Embroidery outline does not match the fill: start with hooping
Another layer of backing will not always close a gap between the fill and outline. Hoop the backing together with the fabric, then compare the problem design with a control design on the same fabric and backing.
Bubbles at the edge of a button badge: fix the laser-printed artwork
On a dark laser-printed background the film slips on the toner and lifts in a bubble at the rim. A 3 mm white ring on the hidden edge of the insert fixes it: here is how to set it and check it.
Color Science for Printers: ICC Profiles, Color Spaces and Calibration
Understanding color science is key to professional printing. Learn how ICC profiles control colors, why RGB and CMYK produce different results, and how to properly calibrate your printer for DTF and sublimation printing with accurate color reproduction.
DTF Ink: Types, Compatibility and Selection Tips
DTF ink — complete guide to types, printer compatibility and selection tips from My Print experts.
Non-Standard Surface Printing: Wood, Metal, Leather, Glass
Discover the possibilities of printing on non-standard surfaces: wood, metal, leather and glass. Detailed overview of UV, DTF and sublimation technologies with practical advice on surface preparation, ensuring adhesion and achieving maximum print durability.
Hoodie Printing: Technologies, Tips and Business Potential
Hoodie printing: technologies, temperature tips and business potential.
7 Textile Printing Technologies: Mega Comparison with Numbers
Comprehensive comparison of 7 main textile printing technologies across 15+ parameters: cost, speed, quality, durability, fabric compatibility. Detailed tables with real numbers for optimal solution selection.
Tear-away or cut-away stabilizer: what should stay beneath embroidery?
Remove excess tear-away backing; leave permanent cut-away beneath the stitches. See how to choose for poplin and knits and finish the reverse neatly.
A large poster from A4 sheets: align the seams and keep its size
Two 190 mm image tiles sharing a 10 mm strip produce a width of 370 mm. Learn how to align the picture, remove the spare edges and keep the poster's size.
DTF RIP Software Selection: Cadlink, Maintop, Photoprint & Alternatives
Comprehensive review of RIP programs for DTF printing with detailed comparison of Cadlink, Maintop, Photoprint and other solutions. Find out which software best suits your needs and budget.
Saddle-stitched booklets: why inner pages lose their outer margin
An even trimmed edge does not guarantee equal margins. See how nested paper thickness changes the space beside text and what to agree before printing a photo portfolio.
Eco-Printing: Sustainable Business Trend in Promotional Products
Eco-printing: trend, technologies and business opportunities.
How to Make Money with Clothing Personalization: 10 Business Ideas
How to make money with clothing personalization? 10 proven business ideas with DTF printing.
Ukraine Personalized Products Market 2026: Data, Trends and Opportunities
Comprehensive analysis of Ukrainian personalized products market: market size $180-220M in 2026, 18-25% annual growth, buyer profiles of 5 main groups, seasonal trends and most promising segments.
DTF Printer Maintenance: Daily, Weekly and Monthly Checklist
Comprehensive DTF printer technical maintenance guide with detailed checklists for daily, weekly and monthly care. Keep your equipment in perfect condition for uninterrupted operation.
How to Start a DTF Printing Business from Scratch: Step-by-Step 2026
Відкрити DTF бізнес можна за 167 000–195 000 грн. Комплект: DTF принтер M330 XP600 + термопрес HP380A + витяжка XS-080. Окупність 5–9 місяців при 100+ нанесеннях/місяць.
Heat transfer vinyl lifts with the carrier: what to do
Remove the clear carrier while leaving the whole design on the fabric: cold and hot peeling, a brief second press and a sample before production.
A white shadow on one side of a DTF print: how to align the layers
A white shadow on one side of a design calls for a layer alignment check. See which test to print and why excessive white underbase choke can damage fine lines.
Photo magnets: print on magnetic paper or mount a finished photo?
A good finished photo can become a magnet without reprinting. Compare the two materials and work out the backing for 18 photos.
Printing Business Franchising: Models, Numbers and Is It Worth It
Comprehensive analysis of franchising in printing business: comparing franchise models with independent startup, real investment figures from $15,000 to $150,000, ROI analysis and payback periods, pros and cons of each approach with specific financial scenarios.
Sublimation Printing for Beginners: Step-by-Step Guide 2026
Сублімаційний друк — нанесення зображень на поліестер через чорнила та термопрес при 190–200°C. Собівартість кружки ~52–59 грн, футболки ~5–6 грн/A4. Стартовий комплект від 12 300 грн.
Legal Aspects of Printing Business: Copyright, Licenses, FOP Registration
Detailed examination of legal issues in the printing business: from copyrights and trademarks to FOP registration and client contract preparation. Learn how to protect your business from legal risks.
UV DTF Printing: What It Is, How It Works and Why It Is the Trend of 2026
UV DTF — наклейки на будь-яку поверхню (скло, метал, пластик, шкіру) без термопресу. Принтер + ламінатор = готова наклейка за 2 хв. Стартовий комплект від $3 500. Рентабельність 300–500%.
Can a Cup with UV DTF Decoration Go in the Dishwasher?
Water resistance does not mean dishwasher durability. When to wash a UV DTF cup for the first time, how to care for it every day and what to offer a buyer who needs a dishwasher-safe mug.
Coloured specks on a sublimated mug: how to find the source
The paper looked clean, but pressing left blue or black specks around the design. Find their source before starting the next batch of mugs.
Scaling Print Business: From 1 to 10 Printers
Scaling a print business is a complex process requiring strategic planning and right decisions. Learn when to buy a second printer, how to hire staff, expand facilities, and delegate management. Practical financial benchmarks and step-by-step growth plan from 1 to 10 printers.
DTF Printer Maintenance: Checklist for Long Life
DTF printer maintenance checklist: daily, weekly, monthly care.
50 Proven Ways to Find Clients for Your Print Business
Comprehensive guide to 50 proven client acquisition methods for print businesses. Free and paid strategies with effectiveness and cost analysis.
Why laminated stickers get water damage at the edges
The laminate is intact, but the sticker’s edge is swelling. See where water enters after cutting and what to change in the sticker’s base and protective layer.
Pale patches after sublimation: pre-press the fabric first
Even colour on the paper, but pale patches on polyester after pressing? Pre-press the fabric for 3–5 seconds before the transfer, let the steam out and cover the print with fresh protective paper, not a PTFE sheet.
Inkjet waterslide decals: when to seal the print before water
Drying the print is not enough: conventional inkjet waterslide decals need protection before water. Follow the sequence and check the outline with a small trial.
Eco-Friendly Printing: How to Make Your Print Shop Green and Profitable
Eco-friendly printing is becoming not just a trend, but a necessity. Consumers increasingly choose eco-friendly products, and governments introduce stricter environmental standards. Learn how to transform your print shop into a green business, use water-based inks, minimize waste, and profit from environmental branding.
DTF Printing Business: From Start to Stable Income
DTF printing business: equipment, financial model and revenue streams.
Mug Printing via Sublimation: Complete Guide from A to Z
Сублімація на кружках — найпопулярніший напрямок для старту. Собівартість кружки 52–59 грн, роздрібна ціна 150–350 грн. Потрібен: принтер Epson L132 (від 8 817 грн) + термопрес для кружок (від 3 450 грн) + сублімаційний папір і заготовки.
How to Sell Custom Print on Marketplaces: Complete Guide
Comprehensive guide to selling custom print products on marketplaces. Platform comparison, listing optimization, product photography, and successful seller case studies.
Numbered tickets: assembling cut piles in order
Put 1, 6, 11, 16 on the first sheet instead of 1, 2, 3, 4. Follow the numbers through five sheets and four cut piles to a finished stack running from 1 to 20.
AI and Artificial Intelligence in Printing Business: What Already Works
Artificial intelligence is no longer the future — it's the present of the printing business. From automatic design generation to smart pricing, AI tools help print shops optimize processes, reduce costs, and improve service quality. Discover which AI technologies already work in the printing industry and how to implement them in your business.
Sublimation vs DTF Printing: What to Choose for Your Business
Sublimation vs DTF: technology comparison, pros and cons.
Print Business Pricing: How to Calculate and Stay Profitable
Complete guide to print business pricing: from cost calculation to pricing strategy selection. Formulas, calculation examples, and common mistakes.
A step after corner rounding: what to check
A small step beside the curve does not necessarily mean a dull blade. Check the blank, both guides and how the card is held before cutting the whole stack.
Laminator jam: how to get the pouch out
Reverse or ABS lever: how to get a jammed pouch out, when to stop, and how to feed the next one so it does not jam.
Seasonal Printing: How to Earn from Holidays Year-Round
Seasonal printing opens opportunities for stable earnings throughout the year. From New Year gifts to graduation souvenirs - each month brings new opportunities to increase profits. Proper planning and preparation help maximize holiday demand.
DTF vs Sublimation: What Is Better for Your Business in 2026
DTF — для бавовни, темних тканин і будь-яких матеріалів (від 167 000 грн, 25–30 грн/A4). Сублімація — для поліестеру, кружок і масового виробництва (від 12 300 грн, 6–10 грн/A4). Детальне порівняння для вибору.
T-Shirt Printing: Complete Guide to Technologies and Equipment
Full overview of t-shirt printing technologies: DTF, sublimation, screen printing and more. Methods comparison and required equipment.
Canvas prints: allow for the sides and rear without losing the picture
Calculate the front, sides and fastening allowance separately. A hypothetical example explains why a 390 × 490 mm blank has a 340 × 440 mm printed area.
Photo Printing vs Vector Printing: When to Use Each Type
The choice between photo printing and vector printing depends on image type, product purpose, and technical requirements. Understanding the differences between raster and vector formats helps achieve the best print quality and optimize production costs.
Circle cutter tearing badge inserts: how to get a clean circle
Ragged edges, oval cutouts and uncut bridges have different causes. Start with one sheet, a steady base and light pressure, then check the blade.
Half-holes at the page edge: how to set up a binding punch
Does the last hole break through the end of your notebook page? Learn how to centre the row, when to disengage the end dies and why larger covers need a separate check.
10×15 photos: keep the whole picture or choose the crop
Photos and paper can have different proportions. One scene shows where white borders come from, what filling the paper removes and how to choose the crop before printing.
How to Choose a Sublimation Printer: Buyer Guide 2026
Для сублімації обирайте Epson L-серію з СНПЧ. Для кружок і A4 — L132 від 8 817 грн. Для A3+ і великого асортименту — L1300 від 29 739 грн. Головне: 6 кольорів, СНПЧ, пьєзоелектрична голівка.
Corporate Merchandise: How Print Shops Earn from B2B
Corporate merchandise is becoming an increasingly profitable niche for print shops. From branded apparel to promotional items and event kits - companies actively invest in corporate identity. Learn about typical orders, bulk pricing strategies, and approaches to attracting corporate clients.
Three-panel brochure: why one panel is narrower
Nested flaps and accordion folds need different layouts. Follow a 97 + 100 + 100 mm teaching example through two folds, both faces of the sheet, cover placement and a labelled paper dummy.
How to Choose a DTF Printer: Comparing Epson Print Heads and Models
Для DTF друку обирайте принтер з голівкою XP600 (бюджетний старт, до 5 м²/год) або i3200 (бізнес-рівень, 7-12 м²/год). Принтер з XP600 від 134 580 грн, i3200 від 596 000 грн.
Complete Printing Business Economics: Financial Model from 0 to $25K/month Revenue
A detailed printing business financial model: from startup investment to $25K/month revenue. Real cost breakdowns, margins, and ROI timelines for DTF, sublimation, and UV DTF printing.
Sublimation Paper: How to Choose and Avoid Mistakes
How to choose sublimation paper: types, specs, mistakes and tips.
Why heat transfer vinyl wrinkles after washing
The print went wavy but the edges hold? Most often the shirt has shrunk. How to flatten the finished garment and what to change in your blanks before the next batch.
UV DTF wrinkles on a tapered cup: how to make the design fit
On a tapered cup, the bottom edge of a wrap must be shorter than the top. Learn when you need a curved template and when you can cut a finished transfer into separate motifs.
Heat Press for DTF Printing: How to Choose and Set Up
Complete guide to choosing and setting up a heat press for DTF printing. Temperature, pressure, dwell time — all the secrets from My Print experts.
Destructible labels or VOID: what remains after removal?
Brittle paper breaks apart; a VOID construction reveals a message or pattern. Compare the results after removal and see what to check before printing a batch.
Embroidery feels stiff after rinsing: how to wash out stabilizer
The stabilizer sheet is gone but the fabric is stiff once dry? Dried residue dissolves again: how to wash it out, how to identify an unlabelled stabilizer and when not to use hot water.
Sublimation paper stuck to a mug: how to remove the residue
Stuck paper does not always mean a ruined mug. Learn how to clean the surface, assess the coating and change one variable in the next trial.
Saddle-stitched booklets: counting pages and the cover
One folded sheet makes four pages. Use a short portfolio example to count the cover, place two extra pages and check the PDF with a paper mock-up.
DTF Printing on Dark Fabrics: Secrets of Vibrant Prints
DTF друк на темних тканинах — завдяки білому підкладу CMYK чорнила дають яскравий принт навіть на чорному. Температура 155–165°C, 12–15 сек, холодний відрив для матового фінішу.
White DTF prints turning pink on polyester: what to change
A white design looked clean after pressing but turned pink the next day? How far to lower the press temperature, when to try black powder and how to test a sample before production.
Guillotine cuts the stack at a slant: top sheets come out shorter
A dull knife pulls the top sheets from under the clamp and the stack comes out tapered. Check the clamp, stack height and knife sharpness, make a test cut and compare the top and bottom sheets.
Black ink smears on glossy stickers: what to change
Why only the black rubs off a glossy sticker and which paper type to choose in the driver so it stays put.
Press marks on polyester T-shirts: how to sublimate without the frame
A line along the sheet edge or a box from the platen is flattened polyester. How to press with a pillow so no frame appears, and what can save a finished garment.
Milky film after laminating: will a second pass help?
Has a glossy pouch come out milky? Check the setting and warm-up. See when to try one more pass and when to look for another cause.
Badge coming apart: check the paper and protective film
An extra film disc or unsuitable paper can prevent a badge from closing. Learn how to check the layers and compare two samples before a production run.
Powder sticks to clear DTF film: static or moisture?
Static and moisture leave a similar powder deposit, but they need opposite fixes. Three simple checks show what holds the powder, and a diagram shows what to do with finished transfers.
Why white heat transfer vinyl turns pink on polyester
A white transfer on polyester can change colour after pressing. See how to test the fabric in 10 seconds and what to change before a production run.
Light and Dark inkjet transfer paper: when to mirror your design
Print orientation depends on which face of the image meets the fabric. Follow one design through two transfer methods and check the result before using a transfer sheet.
Four A6 cards on A4: why bleed needs more room
Four trimmed A6 cards almost fill A4. Add separate bleed to each card, calculate the area needed and compare two on A4 with four on A3.
Which thermopress is better to buy? What to pay attention to when buying
Most of the things with unusual prints that surround us in our everyday life are created using thermopress. The decision of which thermopress to buy depends on the objectives of the purchase, the main tasks and scale of production, equipment parameters.
Types of thermopresses: application, principle of operation, nuances
Clothes and items with original prints have firmly entered our lives and become a fashion trend. Thermopress is widely used in polygraphy to transfer original images from an intermediate paper medium to a selected object.
How to choose a thermopress for mugs: tips and analysis of nuances?
Today, almost every house has a name mug with an individual inscription or drawing. This is an excellent option for a gift for any holiday and for any occasion. Drawing on the mug takes place thanks to special equipment - a thermopress.
Arrival of new thermal mugs for sublimation
A large influx of popular sublimation cups
3D mini vacuum thermopress ST-1520. Covers (1920)
Temperature 180 °. Baking time 350-430 seconds
Tablet heat press HP380A NEW 38X38 (0367)
Temperature 180-200 °. Baking time 60 seconds
Thermopress for cups AP1803 (2598)
The temperature is 190 °. Baking time 210 seconds
Tablet heat press HP450A NEW 40X50 (0368)
Temperature 180-200 °. Baking time 60 seconds
Metal compass 25-70 mm (0083)
updated site
We are glad to welcome you to our updated website. We ...
What is needed for printing on 2D covers
Good day, dear customers! In connection with frequent ...
Novelties of covers for sublimation
Dear clients, partners. In connection with the constant
Arrival of 2D and 3D covers for sublimation
Dear clients, partners. We are pleased to announce that we have received ...
3D mini vacuum thermopress ST-1520
We present to your attention a novelty - 3D vacuum
3D mini Thermopresses ST-1520 are available
Dear customers! We are constantly expanding our range...
Resumption of "Payment in installments" service from Privatbank!
We are pleased to announce that we once again provide the opportunity ...
Installment from Privatbank
We are pleased to announce that purchasing equipment or expenses ...
Reduction of prices on Thermopresses for cups
Start your business or expand your product range...
Aluminum for sublimation is available
Aluminum plates for sublimation already in ...
Advantages of HP thermal presses
the advantages of multifunctional
Blanks for badges
Soon, blanks for
Shortly! HP 8 in 1 with a plate 38 * 38 cm.
A modification of the popular one will soon go on sale
Metal for sublimation
Soon, probably at two o'clock









































































































































































































































