To make a keychain of a given size, divide the desired width by the fraction of the width remaining after shrinking, and the height by the corresponding fraction of the height. Measure these fractions on a cooled test piece made from the same film under the same conditions. They can differ: check the horizontal and vertical directions separately.
In the inkjet printing films section, select the shrink-film subtype and check that it is intended for rigid decorative pieces such as keychains, tags and ornaments. One example of this type is white My Print A4 shrink film (9657). Packaging shrink wrap, ordinary printable PET film and heat-transfer film for clothing do not replace this material. Check the print side and compatible inks for the film you choose.
If you already have repeatable shrink results for your film and an unchanged process, use the ratios you recorded. The method below explains how to establish them for new film or new conditions, and how to confirm the intended contour.
Start with two directions on the test piece
Mark X for horizontal and Y for vertical on the test piece, and note their orientation on the sheet. After processing, measure those same directions: do not rotate the piece in a way that swaps X and Y.
- Cut out a test piece and measure its actual starting width and height. Record the material, its orientation on the sheet and the processing conditions.
- Process it according to the instructions for that particular film. Let it cool before measuring the width and height again for the calculation.
- Divide the cooled dimension by the starting dimension separately for each direction. These are your ratios kX and kY.
Hypothetical test: 50 × 50 mm → 22.5 × 22.5 mm
Teaching values, not product measurements. This example assumes uniform shrinking in both directions. All diagrams are top views; thickness is not shown.
Before heating
After cooling
kX = 22.5 ÷ 50 = 0.45
kY = 22.5 ÷ 50 = 0.45
45% of the starting length remains in each direction. Use this remaining fraction in the calculation.
Work back from the finished 27 × 18 mm
Now set the overall dimensions of the finished contour: 27 mm wide and 18 mm high. Each direction has its own division:
Starting width = desired width ÷ kX
Starting height = desired height ÷ kY
Design calculation: desired contour → starting artwork
Divide each dimension by 0.45
Desired finished contour
Starting contour and print
27 ÷ 0.45 = 60 mm · 18 ÷ 0.45 = 40 mm
The pair shows the same contour, bird artwork and hole. All their linear dimensions change by the same ratio; the ring is excluded from the piece’s overall dimensions.
Making the piece runs in the opposite direction
60 × 40 mm — Cut the contour and punch the hole
↓ Heat as instructed → let cool · Each dimension × 0.45
27 × 18 mm — Measure the finished piece
If your file initially uses the desired 27 × 18 mm dimensions, set it to approximately 222.2% of those dimensions for this example, or enter 60 × 40 mm. That is an increase of approximately 122.2%, not 222.2%. The printed and cut test piece must actually match the starting dimensions used in the calculation.
If the square becomes a rectangle after cooling, kX and kY differ: calculate width and height separately. An averaged scale does not compensate for unequal shrinking: a circular outline can become oval after heating. Even separate calculations for the two axes do not remove local distortion: confirm the actual contour and fit with a test of the intended shape.
45% of the length means 20.25% of the area
Area changes in both directions, so its ratio is the product kX × kY. For our hypothetical square:
Starting area: 100%
50 × 50 mm → 22.5 × 22.5 mm
Area after shrinking: 20.25%
0.45 × 0.45 = 0.2025
50 × 50 = 2500 mm² → 22.5 × 22.5 = 506.25 mm²
The whole large square represents the starting area. The blue square inside represents the area after shrinking at the same scale. Each of its sides is 45% of its starting length.
For width or height, divide by 0.45, not by 0.2025. The area percentage is not a scale for linear dimensions.
Check the hole, text and colour on the finished piece
The hole shrinks with the contour. A starting diameter of 6 mm would become about 2.7 mm only under the same uniform shrink assumption: 6 × 0.45 = 2.7. This estimates geometry; it does not recommend a hole size for a ring.
Hole: hypothetical calculation
Punch before heating
Ø 6 mm
Measure after cooling
Ø 2.7 mm
Enlarged views of the holes, both at the same scale.
Fit hardware only after cooling
Diagram of an installed ring. The ring size is illustrative; check suitability with the actual hardware.
Contour and attachment. Cut the intended shape and punch the hole before heating. After cooling, try the actual ring: check that it passes through, moves near the edge and leaves the material between the hole and the edge intact. A diameter calculation does not establish a convenient attachment or the strength of that material.
Text and fine details. These shrink too. Read the smallest text on the finished test piece and check whether closely spaced lines have merged; adjust the artwork before printing a batch if needed.
Colour. The print may become more intense after shrinking. Assess the cooled piece with the intended artwork and adjust brightness from that result, without a universal lightening percentage.
For a new keychain, follow the calculation with a confirmation piece using its actual contour, artwork and hole. Record the result together with the orientation and conditions so that you can reuse it for the qualified process. If the film, orientation or processing method changes, establish the shrink behaviour under the new conditions; copying another film’s heating settings does not do this.
