26.08.2025

Bubbles at the edge of a button badge: fix the laser-printed artwork

Bubbles at the edge of a button badge: fix the laser-printed artwork

If the film on a laser-printed badge lifts in a bubble at the rim, but a blank circle of the same paper crimps smoothly, the film is slipping on the toner. Leave a 3 mm white ring around the edge of the insert (it hides under the back) and reprint. Keep the insert and film diameters the same.

Why a dark print behaves differently

In button badge blanks, the paper and film wrap around the metal edge together. Over a dense laser-printed area, the film can slip relative to the paper and form an air pocket. It happens most on dark backgrounds: there is more toner there, and the wax in some toners makes the surface slippery. The amount of wax varies from sheet to sheet, so the bubble may appear on only some badges: put the ring on the whole run.

Make two badges on the same paper: one with a blank circle, the other with your print. Do not change the press, die and punch or circle cutter or the circle diameter. If the blank circle crimps smoothly and the printed one bubbles, the toner is to blame. If the blank circle also bubbles, the toner is not the cause: check the paper, film and assembly as described in “Badge coming apart: check the paper and protective film”.

Remove toner only from the hidden edge

  1. Open the artwork. Keep the cut circle, the position of the design and the scale unchanged.
  2. Place a 3 mm white ring over the background along the edge of the cut circle, exactly centred so the strip is the same width all the way round. The printer does not print white: that area stays plain paper.
  3. The background must stay on the face and on the curved side: that part of the allowance shows from the side.
  4. Print a sample, cut a circle of the same diameter and assemble a badge from fresh parts.

One cut circle, two print boundaries

Toner to the edge

Face 58 mm

The background also covers the hidden part of the insert.

An unprinted edge

Face 58 mm

The 3 mm white ring hides under the back.

Insert for a 58 mm badge, top view: 70 mm cut, 64 mm background, dashed line = 58 mm face. The coloured band between the dashed line and the white ring goes onto the curved side.

Start with a 3 mm ring: badge press makers recommend this width. The background still reaches 2–3 mm onto the curved side of the badge. Inspect the badge from the front and side: as soon as a white strip shows, narrow the ring by 1 mm.

A 3 mm ring: how far to print the background

BadgeInsert (cut circle)Background
25 mm35 mm29 mm
32 mm44 mm38 mm
37 mm48.5 mm42.5 mm
44 mm54 mm48 mm
58 mm70 mm64 mm

Take the insert diameter from your die's product page. Background = insert − 6 mm.

Read the sample

On the finished badgeNext action
Smooth film with no white rimKeep this width. Before the run, assemble 2–3 more badges with this artwork.
Smooth film, but white shows on the face or sideNarrow the ring by 1 mm and try again: the background does not cover the visible edge.
The bubble remains, no white showsWiden the ring by 1 mm and assemble another sample.
The bubble remains, and a wider ring exposes a white edgeGo back to the widest ring that shows no white and lubricate the die with silicone, as described below.

If the inserts are already printed

Do not trim printed inserts to the edge of the background: a smaller circle will not reach the fold. The corrected artwork has to be reprinted.

For inserts already printed to the edge there is a second option: a solid silicone lubricant stick. With your finger, rub a crumb the size of a grain of rice in a thin layer only along the tapered edge of the second die station, where the back goes. Do not use aerosols or oil: they leave stains on badges.