On a cup that narrows towards the base, a rectangular UV DTF wrap is too long at the bottom, and that is where the folds come from. Print a continuous design from a curved template shaped to the cup. Cut separate flowers, leaves or lettering apart and apply them one by one.
Where the extra material comes from
On a cylindrical cup, the circumference is the same at the top and bottom of the application area. On a tapered cup, the lower circumference is shorter. Once the top of a rectangular wrap meets, excess material remains below: it forms a fold, overlaps or pulls the design out of alignment.
UV DTF films A and B hold the design before application: remove A before sticking it down and B after pressing it onto the cup.
One width, two different circumferences
Top of the application area
Bottom of the application area
Bottom edge of the rectangular transfer
Example: a 270 mm wide wrap closes around the top, but the bottom needs only 250 mm. Rubbing harder with a squeegee cannot remove the difference.
Try a paper proof while the adhesive is covered
- Mark the top and bottom of the design area on the straight sloping wall. Keep off the rounded base and any ribs or ridges near the rim, and keep the print off the band that touches the lips.
- Use a flexible tape to measure both circumferences at those exact boundaries. Their difference is the extra length at the bottom of a rectangular transfer. The cup's capacity will not tell you the size.
- Print the design on paper at 100% scale, cut it out and wrap it around the cup. Check that the ends meet at the same height, with no folds or unwanted overlap at the bottom.
If the paper also bunches at the bottom, change the template shape. If it lies flat but the transfer goes crooked, check the initial alignment and apply it gradually in small sections. Do not stretch the film or press the whole sheet down at once. If a wave builds up ahead, do not press it down: while that section is not yet rubbed on, lift it back with the B film and lay it again.
A continuous design needs a curved template
The flat pattern for a conical wall is a strip with curved top and bottom edges. Angling the ends of a rectangle is not enough: the top and bottom of the template must be arcs, or the edges will sit unevenly on the cup. Use a template for your blank or make one with paper.
Which shape fits without folds
Cylindrical wall
Rectangular flat pattern
Conical wall
Top: the longer outer arc
Bottom: the shorter inner arc
Flat patterns for the side wall. On the conical pattern, the top and bottom edges are arcs and the side edges are straight.
Wrap paper snugly around the sloping wall without folds and secure the seam. Leave the paper edges uneven for now. Mark the decoration boundaries and seam, remove the paper and cut along those lines. Lay it flat, scan it at actual size and fit the artwork into that outline, bending it into the arc so long horizontal lines and text follow the edges. Repeat the paper fit check. The arcs of a real template are shallow: for a 270/250 mm cup with a 150 mm band they bow by only 4–5 mm, and each bottom corner sits 10 mm inside the top one.
Send only artwork that has passed the paper fit to your UV DTF printer. An already printed rectangular transfer, or a design that must not bend, goes on a cylindrical cup with the same circumference.
Separate motifs: cut the transfer into pieces
Are there clear gaps between the flowers or lettering? Cut the laminated transfer into pieces while A still covers the adhesive. Cut through both films between designs, leaving a little film to hold each piece. Dry-fit the pieces, then remove A and apply them one at a time: each can be positioned independently.
What you can separate without cutting the artwork
Separate elements
Cut through an unprinted gap
Continuous printed background
The cut crosses the artwork
The transfer before film A is removed. Dashed lines show where both films are cut; pink areas mark print that the cut would damage.
Check where the white ink and varnish are laid down in the print job. There must be no print at all in the gap: a continuous clear varnish also joins the designs into one sheet. On a ready-made transfer, tilt the sheet to the light: varnish in the gap shines as a continuous film.
If an individual piece still folds during the dry fit, make it smaller or choose a flatter area.
Before application, wipe the cup with a lint-free cloth and isopropyl alcohol and let it dry; wash an acrylic cup with soap and water instead. On a rough, grainy finish the adhesive touches only the high points and the edges lift: for UV DTF, choose a cup with a smooth finish.
If the fold is already stuck down
If only the clear B film outside the artwork has wrinkled, it does not matter: that film comes off anyway. A crease in the print itself that has already been pressed down cannot be smoothed out or re-laid: the print will stretch or tear, and the adhesive can pull off the coating. Remove that decal: lift an edge with a fingernail or a plastic card and peel it off slowly; a warm hair dryer makes this easier. Clean the area as you did before the first application. Print the new decal from the corrected template, or cut the design into separate pieces.
