If a sheet with intact holes slips out through the seam of the metal binding wire, the wire is under-closed. Move the closer pointer on the binding machine slightly towards the smaller diameter and close the same wire again. Stop as soon as the loops are round and the sheets stay in. Replace a flattened wire with a new one and move the pointer slightly towards the larger diameter.
First look at the sheet that fell out
- The hole is torn through to the edge: the closer is not the cause. Replace the sheet, and for a thick block set a larger punching margin on the binder if it has one: 4.5 or 6.5 mm instead of 2.5.
- The loops do not line up with the holes along the row: the wire has a different pitch (3:1 or 2:1).
- The block is thicker than the wire holds (MyPrint wire cards: 9.5 mm up to about 70 sheets of 80 g/m², 11.1 mm up to 85, 12.7 mm up to 100, 14.3 mm up to 115): take a larger diameter; a wire that is too small will not close however hard you squeeze. How to choose pitch and diameter is covered in “3:1 or 2:1 wire binding”.
Holes intact, pitch matching, diameter right: go on to the closer.
An open seam and an oval need different fixes
Look at the spine end-on. An under-closed loop leaves a way for the sheet to escape. Squeeze further and the ring flattens into an oval: the paper is cramped and the pages turn stiffly.
A sheet can escape
A round loop retains the paper
An oval restricts page turning
A loop seen from the end of the spine.
Set the closer to the wire diameter
The closer is set by the wire diameter on the pack, not by the thickness of the block. Assemble a sample with the same sheets and covers you will use for the run.
Before closing, check that the loops pass through the corresponding holes in every sheet. A sheet that is not on the loops will not be held by the closer.
Place the wire in the closing channel open side down, level along its full length. The closer is usually set with a slider or a round knob on a scale of wire diameters in millimetres or inches (9.5 mm = 3/8″, 12.7 mm = 1/2″). Set the pointer to the diameter on the pack, keep your fingers clear of the jaws and pull the lever once all the way to the stop.
Example: new wire size, old closer setting
You change from 12.7 mm wire to 9.5 mm but leave the closer at its previous mark. The jaws stop too soon for the smaller wire. First move the adjustment to the mark for 9.5 mm, then check the sample. The reverse, 12.7 mm wire at the 9.5 mark, crushes the wire into an oval.
Pushing harder will not help: move the pointer
The pointer sets how close the jaws come at the end of their travel. Moving it towards a smaller diameter closes the loop further; towards a larger one closes it less. Pushing harder on the lever changes nothing: the jaws still stop at the same point.
| What you see | What to change |
|---|---|
| An open seam; an intact sheet slips out | Move the pointer slightly towards the smaller diameter, short of the next mark (for 12.7 mm, towards 11.1). Close the same wire again if its loops are not bent. |
| A round loop; sheets stay in place and turn freely | Change nothing. Note the mark for this wire and paper and start the run. |
| The loop is flattened into an oval | Move the pointer slightly towards the larger diameter. Make the next trial with a fresh wire. To rebind the block, pry the seam open with a flat screwdriver and take the sheets off: a reopened wire will not be round again. |
Check the whole spine
Inspect the seam along the whole spine: at the start, middle and end. If the loops are already flattened at one end but still open at the other, leave the pointer alone. Square up the sheets and seat the wire in the channel open side down along its full length. If the difference remains, close an empty piece of wire at the same setting. If that also closes unevenly, the jaws are not parallel: send the MyPrint technical department photos of both ends of the spine and the binder model.
Turn both covers and sheets in different parts of the block. Pull a sample sheet gently by its outer edge: it should stay on the loops. Continue the run once the sample passes these checks.
