One mug ties up a heater for about 4 minutes including the swap — that is 15 mugs an hour, enough for 10–30 mugs a day. For 50 mugs, take a press with two independent heaters: 2 hours of work instead of almost four. From 150 a day, take the five-mug press: alone you will do 150 mugs in about 3.5 hours instead of 5 hours 20 minutes on two heaters, and with a helper taping the mugs in 2 hours 20 minutes.

The paper wraps the mug tightly and heat tape holds its ends by the handle: the mug is ready for the press.
Where 15 mugs an hour comes from
The full cycle is longer than the timer countdown: the press first recovers its temperature after a cold mug, and after the beep you take the mug out and load the next one.
Example: one heater's cycle, white 330 ml mug
You wrap the next mug while the timer runs, so here the press sets the pace. Count the warm-up, 15–20 minutes, separately: for 10 mugs it is a third of the time, for 150 it hardly matters. Time your first ten mugs and put your own figures into the calculation.
Two and five heaters: count the hands
A second heater doubles output if you load the heaters in turn: while one mug is pressing, you swap the other. In the same example a person spends about 75 seconds per mug (30 on the swap, 45 on wrapping) and keeps two heaters busy without delays — 30 mugs an hour.
In 4 minutes five heaters deliver five mugs, but one person needs 75 seconds for each — that is up to 48 mugs an hour. All five work when a helper wraps mugs in advance: then up to 75 an hour.

Two heaters, and a supply of wrapped mugs on the bench so neither heater stands idle.
What to choose for your volume
All MyPrint mug heat presses heat up to 200 °C with a timer of up to 999 seconds, so you choose them by the number of heaters and the mug shapes.
10–30 mugs a day
One heater
AP1803 or MP160: 10 mugs take an hour including warm-up. Add heaters for latte mugs and tumblers later.
30–80 mugs a day
Two heaters
MP260 or two separate presses: 50 mugs take 2 hours instead of 3 hours 40 minutes.
150 mugs and more
Five heaters
MP560: with two people 150 mugs take 2 hours 20 minutes, alone 3.5 hours.
Mugs between T-shirts and caps
Multifunction press
HP 5 in 1 or 8 in 1 from the multifunction heat presses range: the platen and the mug attachment heat in turn. From 10 mugs a day, put a separate mug press next to it.
Two separate presses instead of an MP260 are worth the extra cost if you print on mugs of two shapes all the time: one stays fitted with the standard heater, the other with a conical latte heater, and a breakdown of one does not stop the work. As of October 2026, the MP260 costs UAH 8,900 and two MP160 presses UAH 11,380.
The MP560 at UAH 18,990 costs almost as much as two MP260 presses (UAH 17,800), and working alone both give the same 48 mugs an hour; the MP560 wins when you have a helper.

1 heater for 330 ml mugs · base for interchangeable heaters

2 heaters with separate controllers · two 330 ml mugs at once

5 stations, each with its own display · mugs 7.5–8.5 cm in diameter
Four options side by side
| What we compare | One heater | Two heaters | Five heaters | Multifunction |
|---|---|---|---|---|
| Mugs per hour | 15 | 30 | up to 48 alone, up to 75 with a helper | 15, the platen sits idle meanwhile |
| 150 mugs incl. warm-up | ≈ 10 h 20 min | ≈ 5 h 20 min | 3.5 h alone, 2 h 20 min for two | ≈ 10 h 20 min |
| Mug shapes | any shape with an interchangeable heater | standard cylindrical 330 ml | standard 330 ml, 7.5–8.5 cm in diameter | cylindrical 7.5 and 9 cm in diameter, latte |
| Who it suits | a start and varied shapes | daily standard mugs | long runs, two people | mugs alongside textiles |
| MyPrint models | AP1803, MP160, 2–5 in 1 sets | MP260 | MP560 | HP 5 in 1, HP 8 in 1 |
Calculation for a white 330 ml mug: 4-minute cycle, 75 s of a person's work per mug, 20 min warm-up. Plug the 2 kW MP560 into a grounded outlet on a circuit that can carry this load, and run no other high-power appliances on it. Use an extension cord only if there is no way around it, and one rated for 2 kW.
The mug shape decides which heater you need
A heater clamps a mug tightly only when diameter and shape match — both are listed on the page of each of the sublimation mugs. Interchangeable heaters are in the heat press spare parts section; 11 Oz in their names means a 330 ml mug.
| Mug | Heater | Where to get it |
|---|---|---|
| 330 ml, cylinder, 8 cm | standard 11 Oz: 12 × 23.5 cm, for 7.5–9 cm diameter | AP1803, MP160 and MP260 supplied for 330 ml mugs; select the 11 Oz heater when choosing a set's attachments. The MP560 uses its own 11.5 × 22.5 cm heater. |
| 425–450 ml, 8.5 cm | large 15 Oz: 15 × 25 cm, for 8–9.5 cm diameter | separately, in spare parts |
| Latte 350 and 500 ml, conical | 350 ml — conical 12 Oz, 12 cm high; 500 ml — 17 Oz, 16 cm high | MP160 and AP1803 sets from “2 in 1”, HP 8 in 1, or separately |
| Thermo mug 450 ml (7.4 cm), thermo bottle 500 ml (7.2 cm) | for thermoses: 6.5–7.5 cm diameter, up to 22 cm long | MP160 thermos press, “5 in 1” sets |
| Wider thermo mug, 7.5–9 cm | 27 × 23.5 cm, up to 27 cm high | MP170, or MP270 with two stations |
“2 in 1” does not mean two mugs at once. In MP160 and AP1803 names it is the number of interchangeable heaters in the set, and they press one mug at a time. The MP260 takes two at once, the MP560 five.

Latte mugs are pressed with a conical heater: in a straight one the narrow part of the mug comes out pale.
The first batch on a new press
Temperature
200 °C
on the press display
Time
180 s
Pale bottom: check warm-up and heater contact first
Pressure
firm
the handle needs effort, but one hand is enough
Warm-up
15–20 min
before the first mug of a batch
White 330 ml mug, standard heater. This is the AP1803 setting; the MP160 manual gives 170–180 °C and 180–230 s.
Make the first mug of every batch a test and look at the bottom of the design. If only the first mugs come out pale at the bottom, the press has not warmed up yet. If every mug does, a thick bottom or poor heater contact is to blame; the article ‘Pale band at the bottom of a sublimated mug: the mug or the press?’ explains how to tell them apart.

A case of white 330 ml mugs holds 36: 2 h 24 min on one heater, 1 h 12 min on two, excluding warm-up.
Frequently asked questions
When do I start the timer: right after closing or when the press is hot again?
According to the MP160 manual, when the press with the mug is back at the set temperature. In total the mug stays in the press for 180–250 seconds, depending on the press power and the mug's mass.
Which thermoses can be printed?
Blanks with a sublimation coating, like those in the sublimation thermo mugs, thermoses and bottles section. Check the blank's diameter against the heater: for the MP160 thermos press it is 6.5–7.5 cm and up to 22 cm long.
Will a conical heater fit my press?
According to their product pages, the 12 and 17 Oz conical latte heaters fit the MP160 and HP multifunction presses, and for the AP1803 they come in sets from “2 in 1”. Check any separate heater against your press model on its page: the MP560, MP170 and MP270 have heaters sold for them.
