18.02.2025

Sublimation paper stuck to a mug: how to remove the residue

Sublimation paper stuck to a mug: how to remove the residue

If sublimation paper sticks to a ceramic mug, let it cool, soften the residue with warm water and remove it with a soft cloth. Most often the image under the white fibres is intact. If the coating comes away with the paper, washing will not save the mug.

Why the paper sticks while the image stays underneath

During sublimation, dye moves into the mug’s polymer coating, and the paper should then come away easily. If overheating softens the coating or the pressure is too high, fibres are pressed into the surface and leave a whitish residue. A damp print, or paper not made for mugs, sticks more often.

Before cleaning

Adhered paper fibres
Coating containing the dye
Ceramic base

After gentle cleaning

Fibres removed
Coating containing the dye
Ceramic base

A section through the mug wall: remove the paper while keeping the dyed coating.

How to clean the printed mug

  1. Let the mug cool. If the sheet did not come off in one piece, do not pick residue off a hot mug: stand it on a heat-resistant surface until it is completely cool. Do not put a hot mug under cold water — it can crack.
  2. Soften the paper. Wrap the mug in a warm wet cloth or soak it for 5–10 minutes in warm water with a drop of washing-up liquid.
  3. Wipe off the softened fibres with a soft cloth or the soft side of a sponge. A melamine sponge wears off the gloss, and a blade or the rough side of a sponge scratches the coating. If the paper resists, soften it further instead of rubbing harder.
  4. Rinse and dry. Wipe it dry and inspect it under side light: a wet surface hides residue.
No fibres, a smooth surface and an intact image

The mug is fine. Check it like any finished mug.

Residue remains, coating intact

Soak it for another 15–20 minutes and wipe again with a soft cloth. Do not use anything harsher. If the residue is still visible once dry, do not give the mug to a client.

The coating is peeling or blistered, or parts of the image come away

Reject this mug. Reheating cannot replace missing coating.

The next mug: change one thing per trial

Use a new mug of the same kind, the same design and a dry print. For an ordinary white 330 ml mug, the typical mug heat press setting is 180–200 °C for about 180 s; if your mug or paper description gives another, use that. Do not leave the mug in the press after the beep: take it out at once and peel the paper wearing heat-resistant gloves.

If the paper has browned and stuck

Dark brown paper means overheating; slight yellowing after pressing is normal. If you press hotter or longer, go back to the typical setting first. If the paper browns and sticks at the typical setting, lower the temperature by 10 °C, for example from 200 to 190 °C. Keep time and pressure the same.

Test on a new mug: an example

Before

200 °C · 180 s

Also note the pressure-adjuster position.

Next trial

190 °C · 180 s

10 °C lower, same time and pressure.

Judge both results: whether the paper comes off cleanly and whether the colour has faded.

If the paper releases and the colour holds, repeat the successful settings on another new mug before starting the batch. If the image turns pale, do not lower the temperature further. Restore the typical setting and check pressure or paper.

If the paper has not browned

If you have to force the handle down, loosen the pressure adjuster: the handle should close with one hand, and the mug should not turn in the closed press. Put the temperature back to typical and keep the time.

If the paper sticks at the typical setting and normal pressure, try another sublimation paper on the same kind of mug. For mugs, use ordinary sheet paper of 100–105 g/m²; tacky paper for fabrics and paper for cotton are not for ceramics. Do not change the mug and the paper together, or you will not know what helped. If the new paper comes off cleanly twice in a row, switch to it.

If the same paper and setting used to work and only a new batch of mugs sticks, the coating is the most likely cause. Set that batch aside and write to us with a photo of the dry surface, the mug and paper names, and the temperature and time.