09.09.2025

Paper curls after roll lamination: what to adjust

Paper curls after roll lamination: what to adjust

If a sheet curls after passing through a roll laminator, start by checking film tension. With double-sided lamination the sheet curls towards the tighter film: if the edges curl up, loosen the upper roll brake; if they curl down, the lower one. Judge by a fresh sample: cut it off the web and let it cool.

Why a well-bonded sheet still curls

Thermal laminating film can bond firmly and still lie on the paper stretched. When the brake is tight, the rollers pull the film by force, and hot film stretches easily. As it cools, it shrinks and pulls the paper with it.

The side under greater tension pulls the sheet into a curve

Balanced tension

Upper film
Printed paper
Lower film

Upper film overtensioned

→ contracts ←

Side view: the tighter upper film shrinks and ends up on the inside of the curve, so the edges curl up.

Tension and roller pressure are separate adjustments. The brake resists the supply roll unwinding; roller pressure squeezes the film and paper together at the nip. Adjust the tension control. The brake is a knob or screw on the roll shaft, one for each roll. The tighter roll is easy to find: with the machine stopped, turn the upper and lower rolls by hand.

Which supply roll to loosen

Mark the top of the test sheet and lay it down the way it left the machine. The rule below is for double-sided lamination.

Edges curl up

Loosen the upper roll brake.

Edges curl down

Loosen the lower roll brake.

One adjustment, one fresh test

  1. Keep the rejected sheet for comparison. Check that both films are threaded as shown on the threading diagram on the machine.
  2. Loosen the brake of the relevant roll by a small step, about a quarter turn. Keep your hands away from the hot rollers and the point where the film is drawn in. Keep the paper, print, temperature and speed unchanged.
  3. Make a fresh test sheet, cut it off the web and let it cool on a flat table. Compare it with the first sheet.

The curl has decreased

Continue in small steps. If loosening introduces wrinkles, restore a little tension. Aim for the lowest tension that lets the film reach the nip without wrinkles. If the tighter roll is already at the wrinkle limit and the curl remains, add a little brake to the opposite roll, in the same small steps.

The curl has not changed. Check in turn:

  • The top and bottom films are the same type and thickness.
  • Both rollers heat. The sheet also curls towards the hotter film, so run double-sided film in the mode that heats both rollers, not in top-heat-only mode.
  • The temperature is not too high. For thin 25 µm thermal film, makers give 100–120 °C; if your film label gives a different range, use that. Lower it in 5 °C steps or add speed while the film stays clear and holds.

If a double-sided sample still curls, send a MyPrint manager a photo of the sample with the top marked, the laminator model, the film, the temperature and the speed.

When only one side is laminated

Film on one side shrinks and the bare paper side does not, so such a sheet curls even at the right tension. On the same machine you reduce the curl like this:

  • brake just a touch tighter than freewheeling;
  • heat on the upper roller only (top-heat mode, if your machine has it), at the lowest temperature at which the film still holds;
  • heavier paper: thin paper curls the most;
  • let finished sheets cool in a stack, face down, under an even weight.

If the curl still gets in the way, laminate the menu or card on both sides: load the same roll at the bottom as at the top and balance the tension as described above. A short run is easier to seal in pouches on a pouch laminator: a pouch has the same film on both sides and no brakes.

Two sheets in one pass: each is coated on one side only

One sheet, two films

Film
Printed paper
Film

Two sheets to be separated later

Film
Sheet 1
Separate here
Sheet 2
Film

After separation, each sheet is laminated on only one side and may still curl.

Cover A4/A3 sticker sheets with self-adhesive cold laminating film: lay it on the sheet and run it through without heat, in a pouch laminator set to cold or in a cold roll laminator. Without heat the film does not shrink, so the sheet curls far less. Print a cover that is laminated on the top only on heavy card and laminate it using the tips above.

On the last third of a roll the same brake pulls harder, so loosen it. After changing one roll, balance both again. Before starting the run, assess a cut, cooled sheet: it should lie flat, with no wrinkles, and the film should not lift anywhere.