07.04.2026

How to replace a page in a plastic-comb catalogue

How to replace a page in a plastic-comb catalogue

In a catalogue bound with a plastic comb, you can replace an individual leaf: a compatible binder mechanism opens the tines and closes them again after the replacement. There is no need to cut a sound comb. With double-sided printing, reprint the correct reverse along with the revised page, even if the reverse content has stayed the same.

First, identify the comb

A plastic comb has a continuous spine and separate curved tines that pass through the holes in the paper. It may also be listed as a plastic binding spring. A continuous spiral runs from one turn into the next; double-loop wire consists of paired metal loops. These constructions do not use the plastic-comb opening method. The link above leads to several types of binding consumables: choose the comb type.

↑ continuous spine

↓ separate curved tines

Part of a plastic comb: separate tines joined to one continuous spine.

Pages 9 and 10 are one leaf

Hypothetical example: the catalogue interior has 40 consecutive pages printed on both sides of 20 individual sheets, or leaves. The front and back covers are separate. Only page 9 needs a correction; all other content and the paper thickness stay the same.

A page is one side of a leaf. In this example, the fifth leaf has page 9 on the front and page 10 on the back. If you remove it and insert a single-sided print of page 9, page 10 disappears. Prepare one new double-sided leaf: revised page 9 + unchanged page 10.

Before: the old leaf

Front · page 9

Top ↑

9

Previous text

Back · page 10

Top ↑

10

Same content

↶ Turn the leaf over

Two views of one intact leaf

After: the new leaf

Front · page 9

Top ↑

9

Revised text

Back · page 10

Top ↑

10

Same content

↶ Turn the leaf over

Two views of one intact leaf

Holes are on the left at the front and on the right at the back: these are views of the same leaf turned over without folding. Page 10 is printed on the new leaf too.

20 − 1 + 1 = 20 leaves

The interior still has 40 pages; put the separate covers back in their places.

Select both required sides in the file by their content and printed numbers: the PDF page index may differ from the number on the page. Print 9 and 10 on one sheet of the same format and thickness. Turn it as you would a catalogue page: the reverse must read the right way up, with the top and binding edge matching the original. Check the duplex setting or manual feed on your own printer.

The same A4 size does not ensure matching holes

Format sets the paper size, not the hole positions. Even on two A4 sheets, the hole row may be offset relative to the top edge, or the holes may have a different shape or spacing.

  1. Take a trial sheet of the same format and paper stock. Punch it on the equipment you will use for the replacement.
  2. Overlay the trial on the original and align the top and side edges. Check the whole row, from the first hole to the last, and the distance from the edge. To compare the sheets freely, you can remove the old leaf after opening the comb.
  3. If the same hole row is simply offset, adjust the guide or feeding method as provided for that machine and punch a fresh trial. If the hole count, shape or spacing differs, you need equipment with the matching punching pattern: moving the guide will not change the pattern itself.
  4. Once the edges and entire row match, punch the final replacement in the verified position.

Grey — original

Teal dashes — trial

Aligned: prepare the replacement

↑ Top edges aligned

Check the entire row

Every hole sits over its counterpart.

Offset: correct the trial first

↑ Top edges aligned

Check the entire row

The edges align, but the holes are offset.

Schematic overlay of two sheets. This shows an offset in an otherwise matching row; the number of drawn holes does not specify a punching standard.

Do not fit the replacement by punching it again at random, stretching the holes or forcing it onto the tines. Use a clean sheet and produce the correct perforation.

Open — replace — close

You need a mechanism for opening plastic combs specifically. The binding equipment category includes different systems; having a punch alone does not mean a machine can open this spine. Follow your binder's procedure for positioning the document, engaging the mechanism and moving the lever.

  1. Support the document and place the comb in a compatible mechanism. Its supports hold the spine while hooks spread the tines and hold them open. Remove paper only when it can slide freely off the tine ends; do not tear it out of a closed comb.
  2. Reach the 9/10 leaf while keeping the remaining leaves in order. If the front section is in the way, temporarily remove it with the front cover as an ordered stack. Remove the old leaf intact, seat all holes of the prepared replacement on the open tines, then put the removed stack back in the same order.
  3. Return the mechanism to its closed position. The tines should return to the spine and retain the whole document. Remove the document and turn through the replacement area.

Black — comb

Blue — binder hook

Thin grey / teal line — old / new leaf

1 · The mechanism opens

→

The spine is held; the hook draws the tine open and holds it there.

2 · Replace the whole leaf

→

↑ Old 9/10 removed over the free tip.

→

↓ New 9/10 seated with its hole over the tine.

3 · The mechanism closes

The hook is released; the tine end has returned to the spine.

Schematic side view: one tine of the same comb and a cross-section of the leaf. The gap in the thin paper line is the hole. The mechanism opens all tines together; in practice, you remove and load the entire row of holes.

Check 8 → 9 → 10 → 11

8
→
9
→
10
→
11

Page 8 should be followed by revised page 9, then unchanged page 10 the right way up, then page 11. Check that each hole is on its tine, the covers are in place and the leaves turn freely. In the example, you removed one leaf and put one back: the interior again has 20 leaves and 40 pages.

Broken tines mean the comb needs replacing. If you add leaves or use thicker paper instead of making an equivalent replacement, check capacity again using the complete document, including the covers. The same page count does not guarantee the same thickness.

Start with the pair of pages on one leaf. Preserve both sides and check the punched holes on a trial before fitting the final replacement in the catalogue.