21.11.2025

Duplex printing: long-edge or short-edge flip?

Duplex printing: long-edge or short-edge flip?

You turn a menu over and the back is upside down. If both pages are upright in the file, first check the flip edge in the print settings. For a portrait sheet turned sideways, choose the long edge. For a landscape sheet turned the same way, choose the short edge. Turning over the top edge reverses those choices.

Start with the reader's movement, then choose the setting

“Long” and “short” refer to the edges of the printing sheet. On a portrait A4 sheet measuring 210 × 297 mm, the side edge is 297 mm long. On a landscape sheet measuring 297 × 210 mm, it is 210 mm. The direction in which paper leaves the tray does not determine this choice.

Duplex mode positions the back according to the selected edge, so it reads correctly after turning the sheet over around that edge. Two upright pages in a PDF therefore do not, by themselves, specify how the reader will reveal the back on paper.

The diagrams below assume: two consecutive pages with the same orientation, one on each side of the sheet, using ordinary duplex printing. Both pages in the file read upright.

Four ways to read the back

Each diagram shows two positions of one sheet: 1 is the front before the movement; 2 is the exposed back after one 180° turnover. The blue line between them is a fixed hinge axis along the edge. A and B identify the same physical paper edges throughout: initially A is at the top and B at the bottom.

Portrait · 210 × 297 mm

Side turn

Long edge · 297 mm

A
↑2 · Back
B
A
↑1 · Front
B

Axis along the side edge

1 on the right → one turnover → 2 on the left

Front: ↑ towards A. Back: ↑ towards A.

Landscape · 297 × 210 mm

Side turn

Short edge · 210 mm

A
↑2 · Back
B
A
↑1 · Front
B

Axis along the side edge

1 on the right → one turnover → 2 on the left

Front: ↑ towards A. Back: ↑ towards A.

Portrait · 210 × 297 mm

Top turn

Short edge · 210 mm

B
↑2 · Back
A
A
↑1 · Front
B

Axis along the top edge

1 below → one turnover → 2 above

Front: ↑ towards A. Back: ↑ towards B.

Landscape · 297 × 210 mm

Top turn

Long edge · 297 mm

B
↑2 · Back
A
A
↑1 · Front
B

Axis along the top edge

1 below → one turnover → 2 above

Front: ↑ towards A. Back: ↑ towards B.

For a side turn, both arrows point towards the same edge A. For a top turn, the front arrow points towards A and the back arrow towards B: after the movement, B is at the top. The back reads upright immediately.

How the sheet moves

Side turn · looking down along the hinge axis

2 · back · 180°

1 · start · 0°

90° · midway through the same movement

Three positions of the same sheet seen edge-on. The dot is the fixed hinge axis; down in this end view is towards the reader. The movement goes from 1 through 90° to 2 and ends with the back exposed.

The hinge edge stays in place while the free edge moves through the space in front of the reader, exposing the other face. Afterwards, do not add a rotation in the plane of the table: it would hide an incorrectly oriented back. Ordinary duplex printing does not require mirrored text either.

Worked example: an A4 menu turned sideways

This hypothetical file has two portrait pages measuring 210 × 297 mm: food on the first and drinks on the second. The side hinge runs along the 297 mm edge, so choose flip on the long edge. The reader turns the sheet sideways and sees the drinks upright.

If that same print is turned over the 210 mm top edge, the drinks will be upside down: the reading movement has changed. If the intended menu will be turned over the top, this portrait layout needs the short edge setting.

Now consider a different layout: both pages are landscape, 297 × 210 mm. Keep the same reading movement, turning sideways. The side edge is now 210 mm, so choose the short edge. Changing only the orientation in the print window while leaving a different layout in the file is not enough: check both the pages and the print preview.

The two-page arrow probe

First establish orientation on one sheet of plain paper approved for your printer and the selected mode. There is no need to print a batch of menus for this.

  1. Create two pages: a large “FRONT ↑” on the first and “BACK ↑” on the second. Each arrow points towards the top of its page. Both pages must match the size and orientation of the intended menu sheet.
  2. Open the finished PDF. View each page separately. If the second page is already upside down in the file, correct it first: the table assumes two upright pages.
  3. In the print window, select the actual printer, the required size and orientation, ordinary duplex mode and the edge shown in the diagram. Use one page per side and no booklet mode for this probe. Check the preview, including whether the application rotates a page automatically.
  4. Print both pages on one sheet. Start with the front upright. Turn the sheet over once, exactly as the menu will be read: sideways or over the top. The back should be readable immediately, with its arrow pointing up.
  5. If the back is upside down, change only the flip edge from long to short or vice versa, then repeat the probe. Keep the file, other settings and reading movement unchanged.

The back now reads upright

Both arrows point up with the intended movement. Record this orientation, mode and edge for this layout, then check the menu material and print appearance.

The edge changed, but the print did not

Check the settings of the actual job. Avoid also rotating the back in the layout by guesswork: first establish whether the selected mode was applied.

Does the setting reach the printer?

A value shown in one window does not prove that this particular probe was sent with it. If changing the setting had no effect:

  • Open printing again from the same application. Check the selected printer and its queue, the list of jobs: are you sending a new probe there, or repeating an old job?
  • Open the selected printer's properties from that window. Check duplex mode and the flip edge, confirm the changes and check the final settings before sending. A saved preset or the application's print window may hold its own values.
  • If the option is missing, unavailable or still produces identical output, check the installed driver, the software that passes the job to the printer, and duplex support for your model and connection method. Repeat the same probe after a confirmed change. An upside-down back alone does not prove a driver fault.

Manual reloading and paper for the menu

With manual duplex printing, orientation also depends on how the sheet is fed again. Mark the front and top of one test sheet, complete the first pass, then follow the driver prompt and your printer's instructions for the second. Record which face and edge you fed in, and check the resulting back. Advice to “always load face down” does not account for different paper paths; the page order for manual printing also depends on the particular process.

For an inkjet menu, choose a double-sided option in the inkjet photo paper category. Coating on both sides provides two printable surfaces, but does not establish compatibility with an automatic duplex paper path. Separately check the paper type, size, grammage, thickness and feed method allowed for your model. An inkjet coating does not establish suitability for a laser printer.

The plain-paper probe establishes top and bottom. Once you have chosen compatible stock, a menu proof checks feeding, drying before the second pass and print quality on both sides. Use the drying requirements for the particular paper, ink and printer.

When a different check is needed

A booklet or several items on one sheet. Imposition means positioning and, when needed, rotating pages on the printing sheet. Booklet mode also arranges their pairs and order for folding. An individual card edge in such a layout may not match the sheet edge. First check both sides of the finished imposition and the corresponding items; do not apply booklet mode again to an already imposed file. The four diagrams above apply directly to one page printed on each side of a sheet.

The top is correct, but front and back are shifted. This is a registration issue: print position, scale or skew. Switching the flip edge is not a millimetre adjustment. Keep the correct orientation and check the position of both sides separately.