13.11.2025

Bubbles under UV DTF on glass: how to apply a smooth decal

Bubbles under UV DTF on glass: how to apply a smooth decal
Apply UV DTF to dry glass gradually: attach one edge, hold the rest above the surface and lower it behind the squeegee. That way the air escapes through the edge that is still free. Press the whole perimeter at once and the air stays inside as a bubble.

Where the air gets trapped

Adhesive around the bubble already touches the glass, while the centre has no contact. Pressing the middle is useless: the air has nowhere to go.

Of the pair of UV DTF A and B films, the lower A comes off before application and the upper B at the very end: you press the print through it.

An air pocket beneath the adhesive

B carrier film
Adhesive
Air
Glass

Cross-section during application. A film has already been removed; the white area shows where adhesive does not touch the glass.

A bubble under clear B film outside the design comes away with the film. A bubble beneath the print remains on the item. Inspect the design in side light before removing B film and again after.

Work from one edge

Wash and dry a new or dirty jar first. Then wipe the application area with a lint-free cloth and isopropyl alcohol (70–99%) and let it dry: the alcohol removes grease and fingerprints and evaporates without residue. Do not use window cleaner: it can leave a film that the adhesive grips less well. The jar and transfer should be at room temperature, about 20–25 °C, with no condensation. From then on, keep your fingers off that area.

Check the position of the transfer while the adhesive is still covered and mark it with a strip of masking tape. Lay the transfer on the table, B film up, and rub the design firmly with a squeegee or a smooth plastic card. Then remove A film, leaving the print on B.

  1. Start at an edge. Touch one edge of the decal to the glass and keep the rest above it. On a jar, this is a vertical edge along the axis: from then on you simply rotate the jar. Choose the position beforehand: a pressed design cannot be moved without damage.
  2. Lower behind the squeegee. Work through B film from the bonded area toward the free area. Let each stroke overlap the previous one slightly so no unpressed strips remain. Hold the free edge above the glass until the squeegee reaches it.
  3. Rotate the jar. On a cylindrical wall, turn the item gradually while supporting the free part of the transfer. Do not wrap the jar with the whole transfer at once, and do not stretch the film.
  4. Burnish and remove B film. Rub firmly through B film over the whole design and its edges. Then peel it away slowly, folding it back at about 180°, almost parallel to the glass.

Give the air an escape route

Edges attached too soon

Trapped air

A closed perimeter around the pocket

Press progressively

Already bonded
Edge still raisedAir →

Squeegee moves toward the free edge →

Top view. On a jar, start from a vertical edge along the axis and rotate the jar: the line of contact stays straight. Start a long wrap from a vertical strip in the middle and work the squeegee to each edge in turn.

If you can already see a bubble

What you seePart of the design is still raised
What to doDo not lower the free edge. With the squeegee, push the bubble through B film toward it, and only then carry on. If the bubble will not move and the area has not been burnished yet, lift it back together with B and lay it down again.
What you seeDesign stuck down, B film still on
What to doDo not remove B yet. Push the bubble toward the nearest edge of the design with short, firm squeegee strokes. If it will not move, remove B: a fine needle will help next.
What you seeB film off, a small bubble will not move
What to doPrick it with a fine needle near its edge, not in the centre. Press the air out through the hole with a finger through a soft cloth, then press the spot again. The tiny hole is barely visible.
What you seeA bump remains after pricking, or there is a speck of dust in the bubble
What to doDo not sell it like this. Warm the decal with a hair dryer, lift an edge with a plastic card and peel it off slowly. Wipe off the adhesive residue with alcohol or adhesive remover (on painted glass, test the remover on a hidden spot first) and apply a new transfer.

Do the same voids or bumps show on an unapplied piece of the same sheet? Then the defect was there before application, and rubbing the jar will not remove it. Run a fingernail over the varnish on an offcut: if it feels tacky, raise the UV lamp power or lower the print speed on the UV DTF printer. If the varnish is hard, send your MyPrint manager photos of both pieces, the film name and your laminating settings.

Can you wet the glass?

No. UV DTF goes on dry glass: soapy water stays under the adhesive and weakens the bond. Use the wet method only if the instructions for your films describe it directly.