Unisex for sublimation perforated medium blue visor (10305) - фото 1 - Blanks for sublimation
Unisex for sublimation perforated medium blue visor (10305) - фото 2 - Blanks for sublimation
Unisex for sublimation perforated medium blue visor (10305) - фото 3 - Blanks for sublimation
  • Unisex for sublimation perforated medium blue visor (10305) - фото 1 - Blanks for sublimation
  • Unisex for sublimation perforated medium blue visor (10305) - фото 2 - Blanks for sublimation
  • Unisex for sublimation perforated medium blue visor (10305) - фото 3 - Blanks for sublimation
  • Unisex for sublimation perforated medium blue visor (10305) - фото 1 - Blanks for sublimation
  • Unisex for sublimation perforated medium blue visor (10305) - фото 2 - Blanks for sublimation
  • Unisex for sublimation perforated medium blue visor (10305) - фото 3 - Blanks for sublimation

Unisex for sublimation perforated medium blue visor (10305)

(0)
In stock
Price:
129.00 грн
Product in cart
  • The date of shipment of the goods: 2026-11-23
  • Ask a question for this product

Payment Cash, Visa/MasterCard, Payment in installments, Instant installments, Cashless settlement.
Delivery By new mail to the branch, post machine or courier at carrier rates.

  • Return guarantee

    We guarantee a refund if you are not satisfied with the product

  • Доставка

    Delivery across Ukraine to any settlement

Description Unisex for sublimation perforated medium blue visor (10305)

Perforated visor for dark sublimation logos

 

A perforated visor in coloured polyester. Sublimation ink is transparent and sits on top of the fabric colour, so only a design darker than the fabric shows: black and dark one-colour logos work best. Full-colour photos are printed on a white visor.

Coloured polyesterfor a dark one-colour logo
Toplessopen crown
56 cmhead size
Hook-and-loop strapadjusts the fit at the back

Is this visor right for you

 
You sublimate a dark one-colour logo or lettering
You have a cap heat press or a cap platen compatible with your press; the heater must cover the whole design and the band must lie against the form without folds
Sublimation gives no white, and light colours in the design mix with the visor colour
You need a full-colour photo — take the white visor

Sizes and print settings

 
band heightlogo or lettering on the front band
1–1.5 cmfrom the peak seam to the design
Temperature
190–200 °Cstart at 190 °C
Time
45–60 sstart at 50 s, counted from closing the press
Pressure
mediumthe handle goes down with moderate resistance

These are starting settings: the exact ones depend on your press, paper, inks and room conditions — temperature and humidity.

Why this visor

 

Design inside the fibres

Under the press the ink passes into the polyester, so there is no film on the band to crack or peel

Perforation

Small holes across the band and peak let air through

How to put a logo on the visor

 
 
Prepare the design
A dark one-colour logo or lettering within the height of the front band; place the bottom of the design 1–1.5 cm above the peak seam. Print it mirrored with sublimation inks on sublimation paper.
 
Cut out the transfer
Leave 1–1.5 cm of paper around the design; if the paper bulges on the curve of the band, snip the top corners.
 
Heat the press
Fit the cap platen and set the starting 190 °C and 50 s. Wait until the press reaches the set temperature.
 
Put the visor on the form
Lay a sheet of protective paper on the lower form, fold the sweatband out, pull the visor over the form with the peak towards you and fasten the hook-and-loop strap: the band must sit tight, without folds.
 
Pre-press the band
Start with a 5 s pre-press without the sublimation transfer; leave the protective paper on the lower form under the band in place. Allow about 10–15 s to cool before fixing the transfer.
 
Fix the transfer
Place it design side down in the centre of the band and tack it with heat tape on the margins only. Place a clean sheet of protective paper on top.
 
Key step
Press
Start at 190 °C, 50 s, medium pressure; do not touch the visor while the timer runs.
 
Peel the paper
Right after the signal, in one motion, without letting the paper fall back.
 
Cool the visor
Let it cool completely before packing; keep weight off the band meanwhile.
Tip: Test the first visor of each batch and assess the print after cooling. If the print is pale, check the paper, inks, moisture, even contact with the band and the effect of the fabric colour on the design. After correcting the cause, adjust the starting settings on a fresh test visor within the stated ranges, changing one setting at a time; record the result.

Sublimation visors: which to choose

 
VariantSublimation printingHead sizeStrap
Perforated visor, blueYou are heredark logos on the perforated band56 cmhook-and-loop
Mesh visor, bluefull colour on the white front band56 cmplastic
Polyester visor, light bluedark logos on the coloured band56 cmhook-and-loop
Polyester five-panel cap, bluedark logos on the coloured front56 cmmetal

Where it works best

 
Run, tournament, training
Visors with a club or race logo for participants and volunteers
Personalised gift
A visor with a name or date printed in one dark colour
Beach and summer events
Logo visors for outdoor promo

What can go wrong

 
Pale print

Cause: possible moisture, uneven contact, unsuitable materials, insufficient heating or the effect of the fabric colour

Fix: check that the band is dry, the paper and inks are suitable, and press contact is even; remember that the fabric colour mixes with the ink; after correcting the cause, adjust the settings on a fresh test visor, changing one setting at a time
A band under the design

Cause: the sweatband stayed under the front of the visor

Fix: fold the sweatband outwards before pressing
A shadow next to the design

Cause: the paper shifted or fell back after pressing

Fix: fix the transfer with heat tape and peel the paper at once in one motion
A blurred design or a dent in the band

Cause: pressure too light or too heavy

Fix: adjust the pressure: the handle should go down with moderate resistance
The visor colour changed under the heater

Cause: possible effects of heat on the fabric

Fix: assess the colour after complete cooling; if the change remains, adjust the settings on a fresh test visor, changing one setting at a time

Questions and answers

 

Will a white or light design print?

Not with sublimation: the ink is transparent and darkens on coloured fabric. Light and colourful designs go onto this visor with a DTF transfer or flex, and full-colour sublimation needs a white visor.

What size should the design be?

Fit the design within the height of the front band. Check the final size on the visor fitted to the press: the heater must cover the whole design within the area of even contact.

How does the perforation affect the print?

The holes stay unprinted, so thin lines and small text break up: logos and lettering with clear, not too thin lines work best. Ink can pass through the holes onto the press form, so a sheet of protective paper goes on the form under the band.

What size is it?

Head circumference 56 cm; a hook-and-loop strap at the back adjusts the fit.

What you need

 

A press and materials for printing on the visor.

Характеристики Unisex for sublimation perforated medium blue visor (10305)

Customer reviews  (0)Leave a review
Customer reviews  (0)

You have already rated this product