29.05.2025

Why laminated stickers get water damage at the edges

Why laminated stickers get water damage at the edges

When a sticker made from self-adhesive photo paper gets soggy at the edges, another layer of laminate will not save the paper base. For bottles and jars, use water-resistant self-adhesive film for inkjet printing made of polyester (PET) or polypropylene (PP): it does not absorb water. Before a batch, test two sample stickers, one dry and one wetted.

Where water enters when the top is intact

Clear cold-laminating film protects the printed face. When the whole sheet is laminated and the stickers are cut out afterwards, the blade cuts the film and the paper along one line. The paper edge stays exposed, and that is where water gets in, even though the top film is intact.

Cross-section of a paper sticker on an object

Shared cut edge ↓
Protective film
Laminate adhesive
Ink-receptive coating and print
Paper base
← water
Sticker adhesive
Object surface

The sticker is on the object: the top is covered, the paper edge is exposed.

Change the base before adding thicker protection

A glossy or matte finish won’t tell you whether there is paper or plastic underneath. Keep self-adhesive photo paper for notebooks and dry packaging. A bottle that gets splashed needs film: PET and PP don’t absorb water, so the cut edge doesn’t swell. In the film category, that means self-adhesive PET or PP marked “water-resistant”, such as the glossy white.

Check these fields on the product page:

Field on the product pageWhat it should say
TypeSelf-adhesive
MaterialPET or PP. Not paper, even if the print on it is water-resistant
Print methodInkjet
FeatureWater-resistant

The film’s product page says lamination isn’t needed because the base is already water-resistant. For a bottle that is washed and wiped, laminate anyway: the laminate protects the print from rubbing and scratches.

A white border does not seal the edge

A white border around the artwork is the same base material without print. Cutting the paper and laminate together leaves that edge exposed too. To seal the edge, apply the sticker to the object, then cover it with a piece of cold-laminating film cut on the cutting plotter to the same outline but 2–3 mm larger on every side. Press the overlap down along the sticker’s edge with a fingernail so no air channel remains under it. On a bottle or jar, do this on the straight wall: on the curves near the neck and base, flat film creases.

White border within the sticker

Artwork

Paper and laminate end at the same cut edge.

Clear overlap onto the object

Artwork

The top film extends beyond the sticker’s edge.

Top view.

The overlap protects the edge from splashes and wiping. For daily washing, the base must still be film.

Try two stickers before making a batch

Print two identical stickers on the material you want to check.

  1. Before laminating, leave the printed sheet to dry overnight: once the film is on, moisture from the ink can no longer escape. The 10–15 seconds on the film’s product page is only the time before you can handle the sheet. Then apply the cold laminate, smooth it down and cut the stickers on the plotter.
  2. Wipe the object with alcohol and let it dry. Apply the samples and press the edges down. Give the adhesive 24 hours at room temperature before the first wetting.
  3. Keep one sticker dry. Hold the other under the tap and rub its edge with a finger, the way the bottle will be washed. Compare the edges and image immediately and again after drying.
What changedWhat to do next
The paper edge swelled or softenedReplace the paper base with a water-resistant film base.
The film is intact, but the colour ranUse film marked “water-resistant”, let the print dry longer before laminating and seal the edge with a clear overlap.
The edge lifted even on the dry sampleDegrease the object with alcohol, round the sticker’s corners and press the edge down harder. If that does not help, the adhesive does not hold on this surface: these films are made for smooth glass, metal and rigid plastic.

Even a water-resistant sticker should not go in the dishwasher or be soaked for long: hot water and detergent lift the edge. Tell your buyers: “Hand wash only”.