06.02.2025

White DTF prints turning pink on polyester: what to change

White DTF prints turning pink on polyester: what to change

A white DTF print on red polyester turns pink because heat drives the fabric dye into the adhesive and white ink. Press such garments at 130–140 °C instead of the usual 160–165 °C and peel the film cold. If the white still turns pink, test black powder or a different fabric, and before production check the colour after a day and after washing.

The dye moves from the fabric into the print

Under the press, dye leaves the polyester fibres and rises through the adhesive into the white ink. On a red shirt the white turns pink, and a sublimated pattern shows through light areas. More white DTF ink covers the fabric better but does not stop the dye. Check the label: polyester blends behave the same way.

After transfer

White ink
Powder adhesive
Red polyester

When the dye migrates

White ink turns pink
↑ Dye moves through the adhesive into the white ink ↑
Red polyester

Cross-section of a white area of a DTF print. Arrows show the dye's path from the fabric.

When exactly does the white change?

Compare the white after it has cooled completely and the next day, under the same light. To tell the causes apart, press a sheet of plain white paper onto a clean area of the shirt for 10 s at your temperature. A pink mark on the paper means the dye is leaving the fabric.

Paper stained, or the white turns pink within a day
This is migration. Lower the temperature, then try black powder or a different fabric.
Paper clean, tint present at once and unchanged
This is show-through. Print a nozzle check and make sure the white layer is solid.

Press at 130–140 °C, not 160 °C

The usual DTF setting of 160–165 °C is exactly what drives the dye out of coloured polyester. On polyester, DTF is usually applied at 130–140 °C, with firm pressure and a cold peel making up for adhesion. Check your T-shirt heat press platen with a contact thermometer or temperature strip: it can run hotter or cooler than the display shows.

Starting settings for polyester. If your powder's instructions give different polyester settings, use those.

StepSetting
Platen temperature135 °C
Pre-press the fabric without the print5 s
Main press10–12 s, firm pressure
Peeling the filmLet the DTF film cool completely, then peel
Final press5 s through a cover sheet at the same temperature

Use a film that can be peeled cold: at 135 °C a hot peel easily lifts the print. Do not add extra presses “to be safe”: they heat the fabric again. Leave the curing of the DTF powder on the film unchanged: the garment is not heated at that stage, so it does not affect migration.

If the white still turns pink at 135 °C

Test black DTF powder with the same settings. On coloured polyester it is used precisely so that the adhesive layer holds the dye back. Black colour is no guarantee, so run production only after a test. Check the edges too: black adhesive can leave a dark rim around white areas. If that does not help either, switch to cotton or a blend with less polyester.

A print that has already turned pink cannot be whitened. A second white transfer on top does not fix it: pressing heats the fabric again, and the dye reaches the new layer as well.

Test before production: today, tomorrow, after washing

Take several garments from the same batch and the same design with a large white area. Press one with your old settings for comparison. Change one thing between samples: the temperature or the powder. Press two samples for each setting: wash one after a day and leave the other for 72 hours. Repeat the test for a new batch of the same colour.

01

After cooling

Record the temperature, time and pressure. Inspect the white area and the edges, and photograph the starting state.

02

After 24 hours

Compare the shade with the start. Check new, strongly coloured fabric or fabric with a sublimated pattern again after 72 hours.

03

After a test wash

After 24 hours, wash the sample inside out and dry it the way your customer will. Check the colour and the edges.

A hot dryer heats the fabric again, so do not skip washing and drying. If the white turns pink, switch to black powder or a different fabric. If edges lift, add 2–3 s or more pressure, not degrees.