If a small letter or dot does not transfer, stop. Lay the film back down, press that spot with a squeegee and keep peeling slowly, folding the film back over itself low over the surface. This saves the detail at both stages: when you peel backing A and when you peel film B off the item.
What holds the design during transfer
In a standard pair of UV DTF films, backing A is coated with adhesive, and the white layer, colour layer and clear varnish are printed on top of it. Film B is laminated over the clear layer: it holds the design from above and carries the separate elements together. This article covers ordinary transfers without foil.
Before application: A + design + B
After application: design on the item
Film B has been removed
Cross-section through the printed area: adhesive and printed layers remain on the item. Both films are removed.
When you remove A, the design should stay on B; when you remove B from the item, it should stay on the item itself. Fine strokes and isolated dots have less bonding area, so press each one down individually.
A detail stays on backing A
- Stop peeling. Lay the films back together exactly as they were.
- Turn the transfer over so film B is face down on a firm, flat table. Rub over the spot of that detail several times with a felt-edged squeegee.
- Peel A slowly, folding it back over itself low over the table: the design stays flat on B and only the backing bends. Before application, check that every dot, fine line and letter ending has moved to B.
If the detail still stays on A, do not apply that transfer. The item is not the cause: the failure happened before the transfer touched it, so the problem is in the transfer itself. If you bought it ready-made, show it to the supplier. If you print your own, let a freshly printed sheet rest for 1–2 hours and check that your films and UV inks are compatible, then check the layer sequence on your UV DTF printer and the settings on your roll laminator; take the temperature and pressure from the instructions for your film pair.
A detail lifts with B on the item
Stop pulling as soon as an edge lifts. Lower B without shifting it and press that particular letter or dot through the film. Do not pick the detail off the film with a finger to apply it separately. Then fold B back over itself, at about 180°. Keep the loose film close to the surface and move your hand along the item. If the same detail lifts again, press it down once more and start peeling B from the other side.
✗ Pulling sharply upward
The film pulls upward on an edge that has not bonded yet.
✓ Peeling slowly back over itself
180°: B folds back over itself as your hand moves along the surface.
Side view. The blue line is film B; the pink edge marks the top of the design.
Fine details are also the first to fail on a cold surface. The item and the transfer should be at room temperature, about 20–25 °C. Let a glass jar or other blank from a cold store or car sit indoors until any condensation has gone, then wipe the area with isopropyl alcohol and let it dry.
On a glass jar, press the design down in short sections, rotating the jar itself. Start peeling B from the side with the larger solid part of the design. Do not apply a transfer across a seam, ridge or raised texture: a detail over a hollow will not reach the surface however hard you rub.
If everything released from A but both small and large areas lift on the item, a slower peel alone is not enough. For the next attempt, wipe the area with alcohol again, let it dry completely and choose an even section without seams or raised texture. On a painted or lacquered item, test the alcohol on a hidden spot first.
When to replace the transfer or change the artwork
The design has torn, shifted or picked up dust on its adhesive. Use a new transfer. Pressing only saves an intact detail: it cannot fix a torn-off piece or dusty adhesive.
The same fine line is lost on several new transfers. If solid areas transfer normally, make the line thicker, enlarge small lettering or remove unnecessary isolated dots. For UV DTF, lines are usually kept at 0.5–0.6 mm or thicker and letters at least 2 mm tall. Before reprinting the whole sheet, print a sample at actual size and apply it to the item.
