28.01.2025

Press marks on polyester T-shirts: how to sublimate without the frame

Press marks on polyester T-shirts: how to sublimate without the frame

The frame is flattened polyester: at 190–200 °C the fibres soften and, once cool, keep the shape the press gave them. It shows where the pressure changes abruptly: at the edge of the sheet or the platen.

To prevent it, put a Teflon pressing pillow inside the garment — larger than the design but smaller than the sheet and the platen. Keep the pressure at medium or below and tear off the paper edges by hand. A finished frame cannot be removed completely: steam and washing soften a faint line, but noticeable shine usually stays.

Why a frame appears

Mills fix the shape of polyester fabric by heating it to 170–210 °C; this is called heat setting. The press does the same: under the platen the knit loops flatten, and the fabric becomes smoother and reflects light differently.

The sheet edge is a step: under the paper the fabric is pressed slightly harder than next to it. The platen edge leaves a rectangular imprint on the fabric.

Where pressure stops, a mark appears

Without a pillow

platen
front
back
lower platen

Pressure on the fabric

| boundaries that will stay on the fabric: platen edge and sheet edge

With a pillow inside

platen
front
pillow
back
lower platen

Pressure on the fabric

Pressure fades gradually, and the sheet and platen edges hang clear of the fabric.

Cross-section diagram: white layer — protective paper, pink — sublimation sheet.

A hard pad under the print area, such as a mouse mat, only moves the line to its own edge. You need a soft pillow with a rounded edge.

Which frame do you have?

Look at the garment under raking light and find your case.

Four marks and what to do about them

A thin line around the design, along the sheet outline

Cause: the paper edge presses into the fabric.

What to change: tear the sheet edge and use a pillow smaller than the sheet.

A rectangle the size of the platen

Cause: the platen edge presses into the garment.

What to change: pillow inside, pressure down to medium.

The whole pressed area shines or yellows

Cause: too hot or too long for this fabric.

What to change: check the platen temperature with a thermometer; on the next test, 5–10 °C lower and 10–15 s longer so the dye still transfers.

A coloured outline or stains

Cause: dye from the Teflon sheet, the lower platen or reused protective paper.

What to change: fresh protective paper for every press; clean the Teflon sheet and the lower platen.

Blue rectangle — the print; outline — the mark on the fabric.

How to press without a frame

Place the design on the flat part of the pillow and the sheet edges beyond it, where the press no longer pushes.

Design < pillow < sheet

press platen

sheet: extends beyond the pillow on all sides

pillow: 1.5–2 cm clearance around the design

design

What goes with what

PrintPillowSheet
logo up to 9×9 cm12×12 cmA5
up to 19×26 cm23×30 cmA3

A larger print needs the 29×38 cm pillow, an even larger sheet and a platen of at least 40×50 cm.

Does your printer only take A4? On a 23×30 cm pillow the sheet edges end up under pressure: tear off the white paper edges and reduce the pressure, and the line will soften. To remove it completely, use a sheet of sublimation paper larger than the pillow, or a smaller pillow that still holds the whole design.

Pressing sequence

  1. Wrap the pillow in clean protective paper and slide it inside the T-shirt under the print area, so the dye does not reach the back and the pillow stays clean.
  2. With the pillow in place, set medium pressure: the pillow lifts the fabric and reduces the pressed area, so the same setting presses harder. On a manual press the handle should close with moderate effort.
  3. Cover the T-shirt with protective paper and pre-press for 3–5 s to drive out moisture and creases. Open the press and remove the top paper.
  4. Place the sheet print side down in the centre of the pillow. Put heat tape outside the pillow: there it is not pressed and leaves no mark.
  5. Cover everything with clean protective paper larger than the platen.
  6. Press using the settings below, peel the sheet and let the T-shirt cool flat: hot polyester still takes on creases.

Starting settings for a polyester T-shirt

Temperature190–200 °C
Time45–60 s, shorter at the higher temperature
Pressuremedium
If the whole area shines5–10 °C lower, 10–15 s longer

If the maker of the T-shirt, paper or ink gives its own settings, use them.

Test a new batch of sublimation T-shirts on one garment or on the inside hem first and inspect it under raking light. Thin polyester is the most sensitive to pressure.

If the frame is already there

It will not come out completely: the mark was set by the same heat as the print. A faint mark can be reduced.

A barely visible line or slight shine

Steam it from a distance without touching the fabric, brush gently with a soft brush and wash: such marks often fade after washing and drying.

Noticeable shine or a brownish tint

Mist the mark with clear table vinegar diluted 1:1 with water, blot and wash. If it stays, cover the mark with a patch: a new sublimation design will not hide it.

Melted fibres

The garment cannot be saved.

Do not re-press the garment hotter or longer: that only adds shine.

When the print is larger than the platen

If the design does not fit under the platen and you press it in sections, every press leaves its own boundary, and a pillow will not help. You need a heat press with a larger platen: 40×50, 40×60 or 60×80 cm.