23.10.2025

Oily DTF transfers: what to change in curing

Oily DTF transfers: what to change in curing

A DTF transfer that is slippery or covered in droplets is usually under-cured: the adhesive has melted, but the moisture from the ink has not left yet. The film normally needs 2–3 minutes at 130–140 °C in the DTF dryer. To check, heat one oily print for another 10 s and compare it with a control once both have cooled.

Why the adhesive melts but the transfer still sweats

DTF inks contain water and moisture-retaining additives that keep the nozzles from drying out. In the dryer, excess moisture needs to escape while the hot-melt adhesive powder melts. With a short heating time, the adhesive can form a continuous layer while moisture remains inside. Moisture and residual additives can later reach the surface, forming droplets or a slippery film.

On DTF film, the layers sit like this:

Melting the adhesive ≠ drying the ink

↑ Excess moisture needs to escape during drying

Melted adhesive
White underbase
Moisture can still remain here
Colour layer
Carrier film

Layer diagram before transfer, print side up. Blue marks indicate residual moisture.

An even sheen on dry adhesive is normal. Look for droplets, a slippery residue and sticking after cooling. Large dark fills are affected most often: they carry the most ink.

Compare two prints to see whether re-drying helps

Take two identical prints from the affected batch. If your dryer is set below 130 °C, first raise it to 130–140 °C. If your powder pack gives a different setting, use that. Leave the garment press setting (160–165 °C) unchanged.

1 · Control

Leave one print unchanged.

2 · Re-dry

≈ 10 s

Heat the second one for another 10 s at the same temperature in a sheet dryer.

No sheet dryer? On a roll-fed line, print the same section twice: in your usual mode and in a slower mode with more passes. Keep the temperature the same: in the slower mode the film stays longer in the heated zone.

Let both cool, compare them and put them side by side in a dry place. Compare them again the next day.

Re-dried sample dry, control oily: the cause is curing. Re-dry the rest of this batch the same way, let it cool and seal it. For new prints, increase the time in the heated zone (next section).

Residue remains or returns on both. A short re-heat did not help. Check the workshop humidity, the amount of white ink in the print profile and drips from the dryer hood (each is covered below). Once you find the cause, reprint any oily transfers from this batch that are meant for orders.

If the film warps or the adhesive turns yellow, it has overheated. Reprint such a transfer if it is meant for an order.

How long the film spends in the heat

In a faster print mode the film passes through the dryer faster and gets less heat. If re-drying helped, measure that time.

Example: a heated path 60 cm long

Time = heated path length ÷ film speed

20 cm/min
3 min
30 cm/min
2 min

Faster print mode → a third less time in the heated zone.

Use a stopwatch to time one design edge from the entrance to the exit of the heated zone; the speed number on the panel will not tell you this. Under 2 minutes: print in a slower mode on the DTF printer or raise the dryer to 140 °C. Change one thing at a time and test with the same artwork.

If re-heating did not help

Check the humidity with a hygrometer next to the printer. Above 60%, run a dehumidifier and keep it at 40–60%: in humid air the film and powder absorb water that the dryer cannot drive out in time.

If droplets fall from the hood onto the film, longer curing will not help: this is condensate from ink vapour. Switch the dryer off, let it cool and wipe the inside of the hood with a degreaser without touching the lamps. Then check the extraction unit: replace an oil-soaked pre-filter, and if you have no extraction, connect a DTF fume extractor.

If the problem started after a change to the printer settings, go back to the profile that gave dry transfers. Extra white ink means extra moisture. But do not cut it until it shows through: colours will look dull on dark fabric.

After the dryer: cool, then seal the packaging

Keep cooled transfers flat, without creases, in tightly closed packaging away from sunlight. Store finished transfers at 15–24 °C and below 60% humidity. Close unused film and powder packaging too. Packaging protects against moisture pickup; it will not dry an already-oily transfer.

If a fresh transfer is dry but becomes oily in storage, compare two cooled samples: seal one and leave the other in your usual conditions. If only the exposed one turns oily, storage is to blame: seal all transfers. If both do, go back to the re-dry trial.

Once the trial works, press one sample with the heat press onto the fabric for the order at your usual press settings. Inspect the print after cooling and again the next day. Before the run, wash the sample inside out after a day.

If oily spots are already on a shirt, do not wipe them. Cover the print with a protective sheet and press for another 5–10 s at the same temperature. If the spots remain or the colour smears, reject the garment, then re-dry or reprint the transfers from this batch.