If new button badge blanks will not sit in the die, do not force them in with the handle. First check the class on the website: MyPrint blanks and dies of one size come in Premium and Standart classes, and the blank class must match the die class. If the class matches and the part still will not sit, dry-fit it in the die in turn with an old, unused one.
Paper is not the issue here: the part will not sit before you even add the paper.
Why matching diameters are not enough
The lower part of the die set has two cavities: A for the shell and B for the back. Each system has its own cavity diameter, profile and depth. An unsuitable shell can catch on the rim, while a back can sit at the wrong height.
In MyPrint's category of presses, die sets and circle cutters, dies of one size come in different classes: Premium (in Talent N3 kits), Standart (in My Print Classic, New Look and Standart Pro kits) and Light. The class is listed in the die's specifications, and the blanks category has a filter for it. Buy blanks of the same class and size as the die. Check the class on the die's own product page: the press name does not define it. No blanks are marked Light; for a Light die, ask the manager which class to take. The size in the name is the diameter of the finished badge, not of a metal part or paper circle.
Do not round inch sizes by eye
2¼ inches × 25.4 = 57.15 mm
The 2¼-inch label is used for both 57 mm and 58 mm systems. Choose blanks by the die class, not by the nearest number.
Compare the fit with the handle up
Raise the handle and take any paper offcuts, film or stuck parts out of cavities A and B. Use unused parts for the comparison: a dismantled badge has already been crimped and reshaped.
No old parts left? Find the die's item code in your order (the number in brackets in the product name) and open its product page: the class is listed there. If the order is lost or the die is not from MyPrint, send the MyPrint manager photos of the die: the upper part and both lower cavities.
- Keep the batches separate. Take one shell from the old pack and one from the new. Make sure you are holding one shell, not two nested together. Check that the backs have not stuck together in pairs either.
- Compare them from the side and above. Look for differences in diameter, height and rim shape. If you have calipers, measure both shells across the outer rim and in height, without squeezing the metal.
- Try the shells one at a time. Place the old shell dome up in cavity A, remove it, then place the new one there. Do not add paper or film yet. Keep the handle up.
- Dry-fit the backs in the same way. Place them in cavity B as you do for work. The edge should sit evenly all the way round; the pin, if there is one, must not lift it. If a thin metal ring from the die kit lies in cavity B, leave it there and dry-fit the old and new backs with it the same way.
One cavity, two different fits
Old part
Sits on the bottom
Oversized new part
Rests on the rim
Cross-section of cavity A before pressing: the old shell sits on the bottom, the oversized one on the rim.
One bent part proves nothing: dry-fit a few intact ones. If none of them sit, the batch is not for your die: check the class.
What the fit check tells you
| Observation | Next action |
|---|---|
| The old part sits; the new one catches, sits higher or rattles with a gap | The batch is not for this die. Compare the class and size on the die and blank product pages and order blanks of the die's class. Do not readjust the press to suit it. |
| Even the old part will not sit | Check that the die is the same size and that each part is in its own cavity: the shell in A, the back in B. Remove any stuck part or offcuts and dry-fit again. |
| Both sit the same way | The fit is fine: if the blank and die classes match, assemble a trial badge (below). |
Do not file the rim or add improvised washers. Buy magnets, keyrings and mirrors of the same class and size as the die; to find out whether they need the ring from the kit, ask the MyPrint manager and give the die's item code.
Make a trial badge and keep a reference
When the class and size match, assemble a trial badge from new parts only: shell, back and film from one pack, on the paper that has already worked. Inspect the crimp all the way around, check that the back holds and the pin closes. Repeat with the next badge before starting production.
If the trial badge does not close and you still have old parts, make the same badge from the old set on the same paper. If the old one closes and the new one does not, the new batch is not for your die: send the MyPrint manager the item codes of the die and the new batch to get blanks of the right class. If the old one does not close either, the blanks are not the cause: check the paper and film using the article “Badge coming apart: check the paper and protective film”.
Keep an unused set and a successful badge in a bag labelled with the die's item code and class and the press name. You will have a reference for the next delivery.
