21.10.2026

Branded Thermo Mug: Cost and Price for 1, 10 and 50 Pieces

Branded Thermo Mug: Cost and Price for 1, 10 and 50 Pieces

A 590 ml tumbler with a wrap-around logo costs a print shop about UAH 443 for a single piece, UAH 397 per piece in a run of 10 and UAH 393 in a run of 50. UAH 330 of that is the blank itself at the MyPrint price as of October 2026; paper, ink and heat tape together come to less than UAH 7. So a longer run lowers only the share of order preparation: with a 30 % markup the client pays UAH 576 for one piece and UAH 510 each for fifty.

What goes into the cost

We work it out on the white 590 ml tumbler with a metal straw from the Thermo mugs, thermoses and thermo bottles for sublimation section. In the MP170, the 27 cm tall heater covers the whole tumbler: we apply the design in one cycle, without turning.

White 590 ml tumbler with a lid and a metal straw

Sublimation thermo mug with a metal straw, white, 590 ml

Metal, glossy white coating · straight cylinder 7.5 cm in diameter · lid and straw · UAH 330 as of October 2026

MP170 heat press for thermoses with a long cylindrical heater

MP170 heat press for thermoses

One heater 27 cm tall for 7.5–9 cm diameters · 0–200 °C · timer 1–999 s · UAH 8,690 as of October 2026

Prices below come from MyPrint product cards as of October 2026. A rate of UAH 200 an hour, 5 % spoilage, the press price spread over 500 items and a tariff of UAH 9 per kWh are the example's inputs: put in your own.

Example: 590 ml tumbler, wrap-around logo

BlankUAH 330.00
A4 sublimation paper, 100 sheets for UAH 288: one sheetUAH 2.88
Ink: up to 1 ml per A4 sheet, 4 × 100 ml set for UAH 689UAH 1.72
10 mm heat tape, 30 m for UAH 92: ≈ 0.7 m for the seam and both edgesUAH 2.15
Spoilage: 5 % of UAH 336.75 of materialsUAH 16.84
Press: UAH 8,690 ÷ 500 itemsUAH 17.38
Labour: 6 min ÷ 60 × UAH 200UAH 20.00
Electricity: 0.55 kW from the press card × 6 min ÷ 60 × UAH 9UAH 0.50
Per pieceUAH 391.47
Layout, mirrored print, check: 15 min ÷ 60 × UAH 200UAH 50.00
Press warm-up: 0.55 kW × 20 min ÷ 60 × UAH 9UAH 1.65
Once per orderUAH 51.65

In a run of 50 the blank is 84 % of the cost. Paper, ink and heat tape together cost UAH 6.75: even twice the ink would add only UAH 1.72.

Where the 6 minutes per piece come from

This is an approximate time for one person working with one press. The order of steps comes from the blank's card and from the article “How a thermo mug is built and why it is pressed differently from ceramics”, which explains where this setting comes from.

1

Layout and print · 15 min per order

Switch the press on first: it warms up while you prepare the layout. The print length is the tumbler's circumference: 3.14 × 7.5 cm ≈ 23.6 cm. Measure the height with a ruler along the straight section. Print mirrored (easier to switch on in the print settings), at 100 % scale, on the white side of the paper. Check the print's length with a ruler and let it dry.

2

Remove the lid, ring and straw · 0.5 min

Only steel goes into the press: set the lid, the silicone ring and the straw aside.

3

Wrap and tape · 2 min

Cut out the print, wrap it tightly around the tumbler with the image facing the wall and fix the seam and both edges with heat tape.

Printed transfer wrapped tightly around a white steel tumbler and fixed with amber heat tape along the seam

The seam and both edges are taped, so the paper will not shift in the heater.

4

Press · 2 min including loading

180 °C, 80 s, medium pressure: the press handle closes easily and the tumbler does not turn in the heater. Make the first thermo mug from every new box a test piece.

A paper-wrapped tumbler next to a tumbler press, its lid and straw apart

The lid and straw lie apart: only the steel tumbler goes into the heater.

5

Peel the paper at once · 0.5 min

At the signal, take the tumbler out wearing heat-resistant gloves, peel the paper at once and let the tumbler cool. While it cools, you wrap the next one.

6

Reassemble and pack · 1 min

Wipe the cooled tumbler, put the lid and straw back and pack it.

That is 6 min per piece. Printing is not added to them: an A4 sheet prints in 2–3 minutes, so the printer keeps the next transfers coming while you press.

1, 10 or 50 pieces: cost and price

Runs differ only in preparation: UAH 51.65 is divided by the number of pieces, and everything else is the same for each piece.

Run1 pc10 pcs50 pcs
Materials with 5 % spoilage353.59353.59353.59
Press and electricity17.8817.8817.88
Labour, 6 min20.0020.0020.00
Preparation: 51.65 ÷ run51.655.171.03
Cost per piece443.12396.64392.50
Price per piece, +30 %576516510
Order total5765,16025,500
Profit on top of labour pay132.881,193.605,875.00
Working time21 min1 h 15 min5 h 15 min

Amounts in UAH. 590 ml tumbler, wrap-around logo, inputs from the example above.

The same markup already makes a piece in a run of 50 UAH 66 cheaper than a single one: that is the preparation spread over the run. A bigger discount comes out of your profit. Say, −20 % off the single-piece price is UAH 461 each, and your profit on 50 pieces drops from UAH 5,875 to UAH 3,425. The biggest saving is in the blank's price: ask a MyPrint manager about the price for runs of 50 or more.

A finished batch of white tumblers with the same colourful pattern lined up before packing

A run of 50 is 5 h 15 min of one person's work; set up a place for the tumblers to cool in advance.

A single piece is the riskiest order. The 5 % spoilage in the cost is an average over many orders. If the only attempt fails, the second blank with paper, ink, tape and 6 minutes of work costs about UAH 357, almost three times the UAH 132.88 profit. So make single orders from a box you have already pressed from without spoilage, not from a new one, and use a higher markup: at +50 % one piece costs UAH 665.

A formula for your own prices

Put in your own prices, minutes and rate. Divide minutes by 60 before multiplying by the hourly rate.

Cost of one piece in a run of N

materials(blank + paper + ink + tape) × (1 + spoilage)
+ presspress price ÷ the number of items you spread it over
+ labourminutes per piece ÷ 60 × hourly rate
+ electricitypress kW × minutes per piece ÷ 60 × tariff
+ preparation(one-off minutes ÷ 60 × rate + press warm-up) ÷ N
+ boxif you hand the piece over in one
pricecost × (1 + markup)

What changes the tumbler's cost:

  • The press has paid for itself: the “press” line disappears and a piece gets UAH 17.38 cheaper. Spread it over 1,000 items and the share is UAH 8.69.
  • The straight section is taller than 20 cm: with the printer's margins the print does not fit on A4. Print on A3 paper at UAH 5.76 a sheet: the paper costs UAH 2.88 more, and the cost per piece with the spoilage allowance UAH 3.02 more.
  • A rate of UAH 300 instead of 200: +UAH 10 per piece and +UAH 25 per order.
  • The logo has to be redrawn: that is design work; charge it separately from the 15 minutes of preparation.
  • Your own ink use: after 20 prints, top up each colour to the same mark with a measuring syringe. The total millilitres added ÷ 20 is the use per sheet.

450 ml car mug: the same formula

The second blank is a white 450 ml car thermo mug with a side handle. The logo goes on the straight section, and we press it in an ordinary mug press: the blank's card allows it, and the 8.5 cm diameter fits the standard heater for 7.5–9 cm, 12 cm tall. The lid comes off, while the black plastic base and the handle stay outside the heater; the setting and the steps are the same as for the tumbler.

Example: 450 ml car mug, logo on the straight section

BlankUAH 255.00
Half an A4 sheet: two prints per sheetUAH 1.44
Ink: up to 0.3 mlUAH 0.52
Heat tape: ≈ 0.25 mUAH 0.77
Spoilage: 5 % of UAH 257.73 of materialsUAH 12.89
AP1803 press: UAH 4,750 ÷ 500 itemsUAH 9.50
Labour: 5 min ÷ 60 × UAH 200UAH 16.67
Electricityup to UAH 0.50
Per pieceUAH 297.29
Preparation, once per orderUAH 51.65
Cost at 1 / 10 / 50 pcsUAH 348.94 / 302.46 / 298.32
Price with a 30 % markupUAH 454 / 393 / 388

Here the blank is UAH 255 of 298.32, over 85 %. So the rule is the same: a longer run lowers only the share of preparation.

White 450 ml car thermo mug with a black side handle

White 450 ml car thermo mug for sublimation

Metal, glossy white coating · 8.5 cm in diameter · side handle · UAH 255 as of October 2026

AP1803 mug heat press

AP1803 mug heat press

One heater for standard mugs · 0–200 °C · timer 1–999 s · UAH 4,750 as of October 2026

Frequently asked questions

A client wants one sample first. How much should I charge for it?

Like a one-piece order: in the tumbler example, UAH 576 at a 30 % markup or UAH 665 at the 50 % worth charging for a single piece. If the client then orders a run with the same layout, they have already paid for the preparation: take UAH 67 at 30 % or UAH 77 at 50 % off the run total — that is the UAH 51.65 preparation with your markup.

Will an ordinary mug press do?

Yes, if the logo is no taller than 12 cm: both blanks, 7.5 and 8.5 cm in diameter, fit the standard 7.5–9 cm heater, and their cards allow it. A design over the full height of the tumbler needs a 27 cm tall heater, as on the MP170. Other models are in the Heat presses for mugs and thermoses section.

Logo on one side or all the way round: which is cheaper?

The difference in paper and ink is under UAH 3: half an A4 sheet and up to 0.3 ml of ink against a whole sheet and up to 1 ml. The blank and the working time affect the price most. A wrap-around design takes longer only when it has to be matched at the seam; add those minutes to preparation.

What should I tell the client about washing?

Advise washing the thermo mug by hand and never putting it in a microwave. A dishwasher only if the blank's maker allows it.