13.09.2026

A white line on a card fold: how creasing helps

A white line on a card fold: how creasing helps

Crease first, then fold

To prepare a printed card on thick paper for folding, crease it: a blunt rule presses the paper into a suitable channel and forms a hinge region. For the method shown here, the raised bead of the crease belongs on the inside of the folded card. Then check the result on the same printed material: creasing helps prepare the fold, but does not guarantee an intact coating on every stock.

What stretches on the outside face

A dark area can look solid on a flat sheet. During folding, the outside face follows a longer arc and stretches. If the printed layer or paper coating cannot accommodate this deformation, cracks appear along the fold; the white base or fibres may show through them. Such marks are especially visible in a dark solid area.

A white line alone does not prove one particular printer fault. First compare the area before creasing, after creasing and after folding: at which stage does the damage appear? Pressing an already damaged fold harder will not restore the coating. Use a fresh printed blank for the next trial.

A crease is a prepared hinge, not a knife cut

A rule with a blunt working edge should enter the centre of a suitable channel. It deforms a strip of paper, leaving a groove on the rule side and a raised bead on the opposite face. Make the final fold along this prepared strip. A knife cuts through the material and does not replace this creasing operation.

A · blue — printed outside face

B · terracotta — future inside face

Cross-sections across the crease line. Thickness and deformation are exaggerated for explanation; the colours identify the same paper faces in every frame, not separate applied layers.

1. Before pressing

Blunt rule

↓

Channel under the rule line

Here A faces up, towards the rule; B faces down, towards the channel.

2. After creasing

Groove on face A

↓
↑

Raised bead on face B

The rule is removed. The sheet is still open; the bead projects from face B.

3. After folding

A stays on the outside

↑

B · inside

The edges fold towards B. The bead points into the space inside the card.

Before running the batch, find the bead on the sample and fold it so the bead is inside. Use the crease shape and the intended faces of the product as your guide; a dark printed area alone does not determine the fold direction, especially with double-sided printing.

How to make a trial on a manual creaser

For a short run of cards, you can add this operation with the My Print CR Base 460 (13211) manual creaser. Its description includes side stops, adjustable creasing depth and a trial on one sheet. These provide a clear setup sequence:

  1. Remove scraps and paper dust from the channel. Identify the required fold line on the printed blank and set the side stop to position it there.
  2. Crease one trial sheet. For coated or laminated material, this model's description advises starting with a shallower impression and increasing it gradually while checking the result.
  3. Check the crease before folding, then fold with the bead inside and inspect both faces. Keep a suitable sample as a reference; during the run, check that the line has not shifted relative to the print.

The aim of adjustment is a usable hinge region without unnecessary damage. If increasing the impression makes the sample worse, do not simply keep going deeper. Pressure values, channel widths or screw-turn counts from other equipment are not settings for this job.

Why a grain rule cannot choose the sample for you

For ordinary folding without a crease, a fold line along the grain is a useful starting orientation: fibres undergo less stretching across the fold. But creasing changes the bending region itself. Tests on coated papers after offset printing include exceptions: after creasing, some materials folded better across the grain, while others performed better along it.

This is neither a new rule to always crease across the grain nor a ready-made setting for digital print. Your sample checks the particular paper, its coating, the print and the action of the tool together. That is why a suitable folded sample matters more than an oversimplified recommendation based only on grain direction.

Two orientations, the same starting conditions

Use paper from one batch with a known grain direction. Prepare two blanks of the same size with the same artwork: include a dark band crossing the future fold. To change the grain orientation relative to the crease, rotate one unfolded card by 90° relative to the other on the press sheet. After printing and trimming, place both samples with the artwork facing the same way. Keep the print conditions, tool and initial creasing adjustment the same. The difference between the samples is grain direction relative to the crease, rather than different artwork or stronger pressure.

Sample A · grain parallel to crease

↕ grain

↕
↕
↕
↕

Dashed line · crease

The same printed band

Sample B · grain across crease

↔ grain

↔
↔
↔
↔

Dashed line · crease

The same printed band

For both samples: crease → fold with the bead inside → inspect.

A teaching diagram of sample preparation, not a display of measured results. Colours do not identify a winner.

If grain direction is unknown, label the trials 'crease along the long edge' and 'crease along the short edge' until you verify it. The long edge of a sheet does not automatically indicate grain direction.

What to compare after folding both samples alike

Coating and print
Where the dark band has cracks or flaking; whether the white base and individual fibres are visible.
Crease line
Whether it is straight and clean; whether there is tearing, delamination or wrinkling even before the final fold.
Opening
Whether the card opens along the prepared line; whether a second, unwanted fold develops beside it.

Compare both samples under the same lighting and opening conditions. Record what you actually see on each and keep the labelled samples. A suitable result means an acceptable appearance and fold action for this particular product, rather than just a less visible white mark.

The trial result may rotate your imposition

Once you choose an orientation, retain it in the layout on the press sheet. If the sheet's grain direction is fixed, rotating the unfolded card by 90° changes the relationship between grain and crease. It is easier to decide this before printing the run than after cracks appear.

If creasing along the grain is suitable

Sheet · grain ↕

Unfolded card: crease ∥ grain

If creasing across the grain is suitable

Sheet · grain ↕

The same unfolded card: rotated 90°

The diagram shows only the orientation of one unfolded card. Calculate margins, allowances, double-sided printing and the number of products per sheet separately. The coloured band rotates with the artwork.

If neither sample is suitable, change one creasing condition that your tool allows, or deliberately choose another material, then repeat the comparison on fresh print. Do not change everything at once: you would lose track of what produced the result. Wetting the finished print or scoring it with a knife is not the next step in this trial.

When a job calls for a different sheet format or an additional operation, compare the creasers and perforators in the MyPrint catalogue. Match the working format and required functions; confirm fold quality on your own printed material. Choose the layout and preparation from a folded sample you are ready to reproduce in the run.