To sell mugs, metal photo panels and mouse pads from day one, buy the kit with the HP230B flat heat press, the AP1803 mug press and the L132 printer for UAH 22,589 (as of October 2026). The box holds both presses, the printer, ink, paper, heat tape, PTFE sheets and 12 mugs. The presses work at the same time: one person makes 12–15 mugs and as many flat items an hour, or 96–120 items in 4 hours at the presses. If you will sell only mugs at first, take the AP1803 kit for UAH 14,106 and add the HP230B later; at current prices, the combined cost is only UAH 68 higher than buying the two-press kit now.

Everything from the box fits on one table.
What is in the box
Most MyPrint sublimation kits come with the A4 L132 printer. Here are the nine items of the two-press kit, as its product card lists them:
| In the box | What for |
|---|---|
| HP230B flat heat press, 23 × 30 cm platen, up to 230 °C | metal, mouse pads, puzzles, a small print on polyester |
| AP1803 mug heat press, up to 200 °C | white 330 ml mugs |
| L132 printer with built-in ink tanks | transfers up to A4 |
| SubliPro ink, 4 bottles of 100 ml | to fill the printer tanks |
| Sublimation paper Premium Classic A4, 50 sheets | 150 mug wraps or 50 flat items |
| Heat tape 5 mm, 33 m | holds the paper on the item |
| 12 white Premium+ mugs 330 ml | tests and first samples |
| PTFE sheet 23 × 30 cm | a layer between the platen and the item |
| PTFE sheet 15 × 22 cm | a wrap over the paper on a mug: protects the heater, optional |

Kit with the HP230B flat heat press and the AP1803 mug heat press + L132
UAH 22,589 · two presses work at the same time · prints up to A4
Bought separately, both presses and the printer cost UAH 22,117, which is UAH 472 less, but the paper, mugs, PTFE sheets and tape in the box would cost about UAH 1,100 more. The mug-only kit — the same, only without the HP230B and the 23 × 30 cm PTFE sheet — costs UAH 14,106; if you later add the HP230B flat heat press to it, the total is UAH 22,656, just UAH 67 more.
Cheaper kits come with the lower-powered MP130 press (300 W against 450 W), and MyPrint gives its setting for the AP1803. The HP 4 in 1 multifunction press in a kit for UAH 23,294 heats one attachment at a time: while a mug is pressing, the metal waits.
What is not in the box
Have ready in advance
What the kit can and cannot do
The AP1803 heats ordinary straight 11 Oz mugs, that is 330 ml; latte mugs, 425 ml mugs and travel mugs need other heaters. The HP230B presses flat items up to 23 × 30 cm, and among fabrics only light-coloured polyester works.
The printer sets the limit: with 3 mm margins, the image on an A4 sheet is up to 20 × 29 cm. A sheet holds three 20 × 9 cm mug wraps or the image for one flat item.

Three 20 × 9 cm wraps on an A4 sheet; before pressing, the colours on the paper look dull.
How many items an hour and a day
Example with MyPrint settings: one person, two presses, transfers printed in advance
Printing the transfers for an hour of two presses takes 32–60 minutes: that is 16–20 sheets at 2–3 minutes each. Print them in advance so you can focus on transferring at the presses.
An order of 36 logo mugs takes 2 h 40 min – 3 h 20 min at the press: 15–20 minutes of warm-up and 12–15 mugs an hour. Printing 12 sheets adds another 24–36 minutes unless you print them in advance. With layouts, printing and packing, MyPrint puts a real day at 30–50 mugs.

Peel the paper off the hot mug right after the beep, wearing gloves.
Three first products
The presses in the kit can make all three products; the blanks cost UAH 30–54. Start every new batch of blanks with a test piece.
1. A 330 ml mug with a photo or a logo
Twelve blanks are already in the box. Setting: 200 °C, 180 s, firm pressure. Materials for one mug come to about UAH 56: the UAH 54 blank plus a third of a sheet, about 0.3 ml of ink and a strip of tape. A white gift box from the “Mug packaging” section adds UAH 7.50.

White sublimation mug, Premium+ class, case of 36
UAH 1,944 · UAH 54 per mug · AAA class, 8 cm diameter
2. A 20 × 30 cm metal photo panel
A white glossy 0.35 mm sheet costs UAH 42, about UAH 47 with paper and ink. Peel the protective film off the metal, tape the transfer down and cover it with a PTFE sheet. Setting: 180–200 °C and 60–90 s, medium pressure; let the metal cool after the press. The sheet is longer than A4, so give the layout a white frame of about 1 cm: on white metal, areas without dye stay white.

Sublimation metal, glossy white, 20 × 30 cm, 0.35 mm
UAH 42 · for indoor use · 180–200 °C, 60–90 s
For an outdoor sign, take metal for outdoor use: a 20 × 30.5 cm sheet costs UAH 67.

The white frame in the layout hides the edge an A4 sheet cannot reach.
3. A 22 × 18 cm mouse pad
A 3 mm pad costs UAH 30, and all the materials for it come to about UAH 34. With an A4 printer, take exactly 22 × 18 cm: the transfer with bleed, 23 × 19 cm, still fits on the sheet, but for 24 × 20 cm it no longer does. The card gives no setting; the maker of such pads recommends 190 °C and 55 s for 3 mm thickness, medium pressure. Do not go above 200 °C: the rubber yellows and hardens.

Rectangular sublimation mouse pad, 22 × 18 × 0.3 cm
UAH 30 · 3 mm · 190 °C, 55 s
What the start costs
Two-press kit and first stock, as of October 2026
Do not buy more paper yet: 48 mugs, 10 panels and 10 pads take 36 of the 50 sheets, and the rest goes on tests.
A mugs-only start — the AP1803 kit, a case of mugs and the boxes — costs UAH 16,320. A computer, gloves and delivery are not in these sums.
The first week
Day 1: set up and fill
In use, the printer takes 48 × 50 cm of the table, and the HP230B needs room at the side to swing the top plate away. Pour the SubliPro ink from the box into the printer tanks, install the driver and print a nozzle check on plain paper.
Day 2: the first mug
Print the wrap mirrored (a tick box in the print settings) on the white side of the paper. Warm the AP1803 up for 15–20 minutes and press the mug for 180 s at 200 °C. If the whole mug is pale, check the print quality and pressure. If both are correct, try 190–195 s on a new mug at 200 °C. If only the bottom is pale, find out whether the mug or the press is to blame.
Day 3: metal and mouse pad
For the first test on metal, set 190 °C and 75 s; on the mouse pad, 190 °C and 55 s. Write the settings that worked on a sheet next to the press.
Days 4–7: samples and first orders
Make one sample of each product for photos and to show customers. Time your own cycle on the first ten mugs so you can quote order deadlines precisely.
Frequently asked questions
Can I fill my own printer with sublimation ink?
A laser printer will not work: it prints with toner. An inkjet that has already had ordinary ink is not a good idea either: mixing inks from different makers clogs the head and changes the colours. That is why the kits come with a separate L132 printer for SubliPro ink.
Is A4 enough if a customer orders a print across a whole T-shirt?
No: an A4 image is up to 20 × 29 cm, which is a chest print on a white polyester T-shirt. For a larger print, there are kits with the A3 L11050 printer and the 38 × 38 cm HP380A press; the entire design must fit on the platen.
Does the press come with a mat?
In the photos on the HP230B card, the lower platen already has a black pad. The silicone mats in the “Heat tape, PTFE, mat” section are bought as replacements.
How long does the paper dry after printing?
Premium Classic, according to its card, dries almost at once: print, cut and tape it to the item.
