28.03.2025

10×15 photos: keep the whole picture or choose the crop

10×15 photos: keep the whole picture or choose the crop

If a photo has a 4:3 aspect ratio and the print is 3:2, you cannot keep the whole scene and fill the paper to its edges without distortion. Fitting the photo leaves white borders; filling the paper removes part of the picture. If everyone needs to stay in the photo, first check whether a crop boundary cuts through a head, shoulder or shoe.

Start by comparing the two rectangles

When choosing photo paper for inkjet printing, compare the exact sheet dimensions on the packaging with the size selected in the driver. The name “10×15” does not always mean exactly 100×150 mm: 4×6-inch paper measures 101.6×152.4 mm. In landscape orientation, the width and height swap places.

Our example uses a 4000×3000-pixel file: its width-to-height ratio is 4:3. The print rectangle is exactly 150×100 mm, or 3:2. It is wider relative to its height than the photo. That difference creates the choice between borders and cropping.

One scene, two ways to place it on paper

Geometric example: an ideal 150×100 mm rectangle, proportional scaling, centred placement and no additional driver enlargement. The drawing is schematic; both blue outlines represent the same paper size.

The whole picture, with borders

Fit the photo to the height

Paper: 150 mm wide × 100 mm high

The photo measures 133.333…×100 mm. The white paper on the left and right forms borders of approximately 8.333 mm each. The hat and flower near the edges stay intact.

To the edges, with a crop

Fill the width of the paper

Paper: 150 mm wide × 100 mm high

The scaled photo measures 150×112.5 mm. A 6.25 mm strip at both the top and bottom lies outside the paper and will not appear in the print.

Blue outline: the paper boundary.

Pink strips: parts of the photo outside the paper.

The pink strips continue the same drawing and show lost parts of the scene; they are not borders. The actual borders in the whole-picture version are white. The people, mountains, hat at the top and flower at the bottom share the same original coordinates in both views.

Where 8.333 mm and 6.25 mm come from

Fitting: a height of 100 mm

100 × 4 / 3 = 133.333… mm

(150 − 133.333…) / 2 = 8.333… mm

The photo is 133.333… mm wide. The remaining paper width is divided into two side borders. The value 8.333 mm is rounded to the nearest thousandth of a millimetre.

Filling: a width of 150 mm

150 × 3 / 4 = 112.5 mm

(112.5 − 100) / 2 = 6.25 mm

The photo is 112.5 mm high. The paper rectangle holds 100 mm; with centred placement, the extra 12.5 mm is split equally between the top and bottom.

These numbers describe the geometry of the example, not a printer tolerance. The actual printable area may be smaller than the sheet. Sharpness and whether the file has enough pixels for the chosen size are separate questions.

Move the crop window, then check the opposite edge

To fill the paper, set the crop to the aspect ratio of the intended print: 3:2 in this example. Move that window over the photo to decide which parts matter most. Moving it up preserves more of the top but removes more from the bottom.

Paper: 150 mm wide × 100 mm high

The same 3:2 crop window has moved to the top edge of the photo. Nothing is removed at the top; the full 12.5 mm of excess height is now outside the paper at the bottom.

The hat stays; the flower goes

In this position, the hat is intact, but the flower and part of the footwear at the bottom will not print. If both edges matter, return to the version with white borders. Moving the window redistributes the crop between the edges.

Do not make the photo fit by stretching only its width or height: faces will look wider or narrower. The DPI/PPI number itself, meaning dots or pixels per inch, does not change the aspect ratio either. It cannot remove the difference between 4:3 and 3:2.

What the print preview should show

Commands have different names in different applications. Focus on the image that will result after all print settings are applied:

  1. The correct sheet and orientation. The preview dimensions match the paper and the size selected in the driver.
  2. For the whole scene, every edge of the original photo and visible borders. For filling the paper, the chosen part of the photo reaching the paper edges; compare it with the original to see exactly what disappears beyond each boundary.
  3. Important details remain inside. After every adjustment, check the top and bottom as well as the left and right edges. People should retain their natural proportions.
  4. The agreed result is saved in a print copy: either the whole picture with borders or a deliberately chosen crop. Keep the original for other formats.

Check borderless enlargement separately

Even when the photo already matches the paper's proportions, borderless mode may enlarge it further and push part of the image beyond the sheet. This is a separate loss of edges that can add to your chosen crop. Whether the mode is available and how much it enlarges depend on the printer, paper size and media.

Check this behaviour in your own driver. If it allows you to reduce extension beyond the edge, assess the result again: borders may appear. There is no universal percentage for every printer. If the application's preview does not show the driver's effect, use the driver's own preview where available, and check the edges of one trial print before printing a batch.

The decision is ready when you can show the intended print and say what will remain on the paper: the entire scene with borders or a specific part without them.