Thermal mug for sublimation "Yeti" with a silver handle (350 ml) (10723) - фото 1 - Blanks for sublimation
Thermal mug for sublimation "Yeti" with a silver handle (350 ml) (10723) - фото 2 - Blanks for sublimation
Thermal mug for sublimation "Yeti" with a silver handle (350 ml) (10723) - фото 3 - Blanks for sublimation
  • Thermal mug for sublimation "Yeti" with a silver handle (350 ml) (10723) - фото 1 - Blanks for sublimation
  • Thermal mug for sublimation "Yeti" with a silver handle (350 ml) (10723) - фото 2 - Blanks for sublimation
  • Thermal mug for sublimation "Yeti" with a silver handle (350 ml) (10723) - фото 3 - Blanks for sublimation
  • Thermal mug for sublimation "Yeti" with a silver handle (350 ml) (10723) - фото 1 - Blanks for sublimation
  • Thermal mug for sublimation "Yeti" with a silver handle (350 ml) (10723) - фото 2 - Blanks for sublimation
  • Thermal mug for sublimation "Yeti" with a silver handle (350 ml) (10723) - фото 3 - Blanks for sublimation

Thermal mug for sublimation "Yeti" with a silver handle (350 ml) (10723)

(0)
Color:
In stock
Price:
320.00 грн
  • The date of shipment of the goods: 2026-11-23
  • Ask a question for this product

Payment Cash, Visa/MasterCard, Payment in installments, Instant installments, Cashless settlement.
Delivery By new mail to the branch, post machine or courier at carrier rates.

  • Return guarantee

    We guarantee a refund if you are not satisfied with the product

  • Доставка

    Delivery across Ukraine to any settlement

Description Thermal mug for sublimation "Yeti" with a silver handle (350 ml) (10723)

A silver Yeti-style mug for a logo on metal

 

A 350 ml Yeti-style steel mug: a silver steel body, a handle in the body colour and a clear lid with a slider. The body is straight, Ø 8.7 cm; the sublimation coating is on the outside of the body. Sublimation ink is transparent, so the silver metal stays in place of any white in the design — the choice for logos and lettering. The body is printed in a standard 11 oz heater for 7.5–9 cm with room for the handle. MyPrint's starting settings for tumblers are 180 °C, 80 seconds, medium pressure.

350 mlvolume
Silvermetal for a logo
180 °Cstarting settings, 80 s
Sliderin the clear lid

Is this mug right for you

 
Your 11 oz heater fits the Ø 8.7 cm body, makes close contact, covers the full design height and leaves the handle outside
You print with sublimation ink on sublimation paper
You need a logo or lettering that sits on metal
For a white background under a photo, see the white Yeti-style mug
The design has to run under the handle — the heater leaves the handle zone out

Size and print settings

 
Ø 8.7 cmstraight body
≈ 27.3 cmapproximate body circumference
Handlein the body colour
Temperature
180 °Cstarting point for a tumbler in a press
Time
80 sfrom closing the preheated press
Pressure
mediumthe press handle closes easily and the mug does not turn

These are starting settings for a heater that wraps the body all round. Tune the exact values to your press, paper, ink and room conditions — temperature and humidity — on a test mug.

Why this mug

 

Like an ordinary mug, but steel

A handle and a slider lid — for coffee at home, at the office or on a hike

Metal under the logo

Unprinted areas stay silver

From file to finished mug

 
 
Prepare the layout
Measure the body height and the usable print width, allowing clearance beside the handle.
 
Print mirrored
With sublimation ink on sublimation paper.
 
Remove the lid
Only the body goes into the heater; the handle stays outside.
 
Fix the paper
Fit the paper tightly within the checked print area, leaving clearance beside the handle, and secure it with heat-resistant tape along the edges.
 
Key step
Press
Starting settings — 180 °C, 80 seconds, medium pressure in an 11 oz heater.
 
Remove the paper
Right after the signal, wearing heat-resistant gloves.
 
Put the lid back
Once the body has cooled completely, put the lid back in place.
Tip: Make the first mug from each new box a test piece. If the design blurs, give the next one 15 s less; if it is pale everywhere, check the press warm-up and paper contact, then add 10–15 s. Change one setting at a time.

Yeti-style mug: which to choose

 
VariantColourVolumeDesign and use
Silver, 350 mlYou are hereSilver metal350 mlA logo on metal
White, 350 mlWhite background350 mlPhotos and full-colour layouts

Where it works best

 
Corporate gifts
A logo on silver metal
A gift for him
A name or lettering on a steel mug
Hiking clubs
A steel mug with an emblem for hikes

What can go wrong

 
A pale band on one side or a pale edge

Cause: the paper or heater does not make contact, or heating is uneven

Fix: check paper and heater contact and the press warm-up; a gap cannot be fixed with more time
A pale band near the handle

Cause: the design ran into the handle zone, where the heater makes no contact

Fix: keep the handle zone free
The design blurred

Cause: overheating

Fix: give the next mug 15 s less
Pale all over

Cause: underheating or weak paper contact

Fix: check the press warm-up and paper contact, then add 10–15 s on the next one

Questions and answers

 

What are the print settings for this mug?

MyPrint's starting settings for tumblers are 180 °C, 80 seconds, medium pressure, in a heater that wraps the body all round. If the design blurs, give the next one 15 s less; if it is pale everywhere, check the warm-up and paper contact, then add 10–15 s. The exact values depend on the press, paper, ink and room conditions, so make the first mug from a new box a test piece.

Which heater does it need?

A mug heater for a 7.5–9 cm diameter: the standard 11 oz heater in a mug press such as the AP1803, or the 30 oz heater in the MP170 press. Before buying a separate heater, ask the manager to confirm compatibility with your press. Before the first print, check that the heater makes close contact with the body, covers the full design height and leaves room for the handle.

What do I do with the lid when printing?

Remove it: only the body goes into the heater. The handle stays on — it remains outside the heater.

White or silver — which to choose?

For a logo on metal, silver: white areas of the design stay metal. For photos and full-colour layouts, white.

How should a printed mug be washed?

By hand, with a soft sponge, without abrasives. Never in a microwave: it is metal.

What you need for printing

 

Equipment and materials for your chosen sublimation printing method.

Характеристики Thermal mug for sublimation "Yeti" with a silver handle (350 ml) (10723)

Customer reviews  (0)Leave a review
Customer reviews  (0)

You have already rated this product