Thermal mug for car sublimation, metal (steel 201, plastic inside), silver (400 ml) (10007) - фото 1 - Blanks for sublimation
Thermal mug for car sublimation, metal (steel 201, plastic inside), silver (400 ml) (10007) - фото 2 - Blanks for sublimation
  • Thermal mug for car sublimation, metal (steel 201, plastic inside), silver (400 ml) (10007) - фото 1 - Blanks for sublimation
  • Thermal mug for car sublimation, metal (steel 201, plastic inside), silver (400 ml) (10007) - фото 2 - Blanks for sublimation
  • Thermal mug for car sublimation, metal (steel 201, plastic inside), silver (400 ml) (10007) - фото 1 - Blanks for sublimation
  • Thermal mug for car sublimation, metal (steel 201, plastic inside), silver (400 ml) (10007) - фото 2 - Blanks for sublimation

Thermal mug for car sublimation, metal (steel 201, plastic inside), silver (400 ml) (10007)

(0)
Color:
Volume:
In stock
Price:
200.00 грн
Product in cart
  • The date of shipment of the goods: tomorrow (23.11.2026)
  • Ask a question for this product

Payment Cash, Visa/MasterCard, Payment in installments, Instant installments, Cashless settlement.
Delivery By new mail to the branch, post machine or courier at carrier rates.

  • Return guarantee

    We guarantee a refund if you are not satisfied with the product

  • Доставка

    Delivery across Ukraine to any settlement

Description Thermal mug for car sublimation, metal (steel 201, plastic inside), silver (400 ml) (10007)

A silver 400 ml car travel mug for a logo on metal

 

A 400 ml car travel mug: a silver steel body, a black lid with a drinking opening, a black handle and a black base. The wide upper part of the body is straight, with a narrower base intended for a car cup holder; check the fit in your vehicle. The mug has a steel outer wall with a sublimation coating and a plastic inner wall. It withstands pressing at the starting settings. Sublimation ink is transparent, so the silver metal stays in place of any white in the design — the choice for logos and lettering. The wide Ø 8.5 cm straight part is printed in a standard 11 oz heater for 7.5–9 cm with room for the handle. MyPrint's starting settings for tumblers are 180 °C, 80 seconds, medium pressure.

400 mlvolume
Silvermetal for a logo
180 °Cstarting settings, 80 s
Plastic insideinner wall

Is this mug right for you

 
Your 11 oz heater fits the Ø 8.5 cm body, makes close contact with the wide part, covers the full design height and leaves the handle outside
You print with sublimation ink on sublimation paper
You need a logo or lettering that sits on metal
For a white background under a photo, see the white car travel mug
For steel inside as well, see the silver 450 ml car travel mug
The design has to run onto the narrower lower part — the heater makes no contact there

Size and print settings

 
Ø 8.5 cmwide straight part
≈ 26.7 cmapproximate circumference of the wide part
Steel outsidethe wall with the print coating
Temperature
180 °Cstarting point for a tumbler in a press
Time
80 sfrom closing the preheated press
Pressure
mediumthe press handle closes easily and the mug does not turn

These are starting settings for a heater that wraps the body all round. Tune the exact values to your press, paper, ink and room conditions — temperature and humidity — on a test mug.

Why this mug

 

Made for the road

A lid with a drinking opening, a handle and a narrower base for a cup holder

Metal under the logo

Unprinted areas stay silver

From file to finished mug

 
 
Prepare the layout
Measure the height of the wide straight part and the circumference without the handle zone; add a paper overlap at the seam.
 
Print mirrored
With sublimation ink on sublimation paper.
 
Remove the lid
Only the body goes into the heater; the handle stays outside.
 
Fix the paper
Tightly all round on the wide part, with an overlap at the seam, and secure it with heat-resistant tape along the edges.
 
Key step
Press
Starting settings — 180 °C, 80 seconds, medium pressure in an 11 oz heater.
 
Remove the paper
Right after the signal, wearing heat-resistant gloves.
 
Put the lid back
Once the body has cooled completely, put the lid back in place.
Tip: Make the first mug from each new box a test piece. If the design blurs, give the next one 15 s less; if it is pale everywhere, check the press warm-up and paper contact, then add 10–15 s. Change one setting at a time.

Car travel mug: which to choose

 
VariantColourVolumeDesign and use
Silver, 400 mlYou are hereSilver metal400 ml, plastic insideA logo on metal
Silver, 450 mlSilver metal450 mlA logo on metal
White, 450 mlWhite background450 mlPhotos and full-colour layouts

Where it works best

 
Corporate gifts
A logo on silver metal
A gift for him
A name or lettering on a steel travel mug
Car dealers and taxi fleets
Understated branded merch

What can go wrong

 
A pale band on one side or a pale edge

Cause: the paper or heater does not make contact, or heating is uneven

Fix: check paper and heater contact and the press warm-up; a gap cannot be fixed with more time
A pale band at the bottom of the design

Cause: the design ran onto the narrower part, where the heater makes no contact

Fix: keep the design within the wide straight part
The design blurred

Cause: overheating

Fix: give the next mug 15 s less
Pale all over

Cause: underheating or weak paper contact

Fix: check the press warm-up and paper contact, then add 10–15 s on the next one

Questions and answers

 

What are the print settings for this mug?

MyPrint's starting settings for tumblers are 180 °C, 80 seconds, medium pressure, in a heater that wraps the body all round. If the design blurs, give the next one 15 s less; if it is pale everywhere, check the warm-up and paper contact, then add 10–15 s. The exact values depend on the press, paper, ink and room conditions, so make the first mug from a new box a test piece.

Which heater does it need?

A mug heater for a 7.5–9 cm diameter: the standard 11 oz heater in a mug press such as the AP1803, or the 30 oz heater in the MP170 tumbler press. Before the first print, check that the heater makes close contact with the wide part, covers the full design height and leaves room for the handle.

What do I do with the lid when printing?

Remove it: only the body goes into the heater. The handle stays on — it remains outside the heater.

Will the plastic inside withstand pressing?

Yes: this mug is pressed at the same starting settings as the steel ones.

White or silver — which to choose?

For a logo on metal, silver: white areas of the design stay metal. For photos and full-colour layouts, white.

How should a printed mug be washed?

By hand, with a soft sponge, without abrasives. Never in a microwave: it is metal.

What you need for printing

 

Equipment and materials for your chosen sublimation printing method.

Характеристики Thermal mug for car sublimation, metal (steel 201, plastic inside), silver (400 ml) (10007)

Customer reviews  (0)Leave a review
Customer reviews  (0)

You have already rated this product