Vintage Cotton Heat Six Blade Cap with Mesh and Elastic Frayed maroon (10318) - фото 1 - Blanks for sublimation
Vintage Cotton Heat Six Blade Cap with Mesh and Elastic Frayed maroon (10318) - фото 2 - Blanks for sublimation
Vintage Cotton Heat Six Blade Cap with Mesh and Elastic Frayed maroon (10318) - фото 3 - Blanks for sublimation
  • Vintage Cotton Heat Six Blade Cap with Mesh and Elastic Frayed maroon (10318) - фото 1 - Blanks for sublimation
  • Vintage Cotton Heat Six Blade Cap with Mesh and Elastic Frayed maroon (10318) - фото 2 - Blanks for sublimation
  • Vintage Cotton Heat Six Blade Cap with Mesh and Elastic Frayed maroon (10318) - фото 3 - Blanks for sublimation
  • Vintage Cotton Heat Six Blade Cap with Mesh and Elastic Frayed maroon (10318) - фото 1 - Blanks for sublimation
  • Vintage Cotton Heat Six Blade Cap with Mesh and Elastic Frayed maroon (10318) - фото 2 - Blanks for sublimation
  • Vintage Cotton Heat Six Blade Cap with Mesh and Elastic Frayed maroon (10318) - фото 3 - Blanks for sublimation

Vintage Cotton Heat Six Blade Cap with Mesh and Elastic Frayed maroon (10318)

(0)
In stock
Price:
198.00 грн
  • The date of shipment of the goods: tomorrow (23.11.2026)
  • Ask a question for this product

Payment Cash, Visa/MasterCard, Payment in installments, Instant installments, Cashless settlement.
Delivery By new mail to the branch, post machine or courier at carrier rates.

  • Return guarantee

    We guarantee a refund if you are not satisfied with the product

  • Доставка

    Delivery across Ukraine to any settlement

Description Vintage Cotton Heat Six Blade Cap with Mesh and Elastic Frayed maroon (10318)

Vintage mesh cap with crossed elastic bands for DTF, flex and embroidery

 

The visor edge is frayed. The logo goes on with a DTF transfer or flex on a cap heat press, or is embroidered.

Cottonwashed, with wear and small rips
Mesh and elasticat the back; two elastic bands cross over the ponytail opening
56 cmhead size
Hook-and-loop strapadjusts the fit at the back

Is this cap right for you

 
You apply DTF transfers, flex or embroidery
You have a cap heat press or a cap platen
The front has deliberate wear and small rips: place the logo on a smooth area and check the bond on a test cap
You print with sublimation — take a trucker cap with a white polyester front

Sizes and transfer settings

 
up to 10 × 5.5 cmtrial guide; check the design against the cap and platen
1–1.5 cmfrom the visor seam to the design
contact beside the seamthe seam may prevent adhesion; test before production
Temperature
150–160 °Creference for DTF and flex
Time
10–15 sfollow the film manufacturer's instructions
Pressure
mediumreference only; follow the film's pressure instructions

These are starting settings: the film maker gives the exact ones, and they are tuned to your press and room conditions — temperature and humidity.

Why this cap

 

A worn-in look

Uneven colour and wear along the seams give the cap character, so even a simple logo looks good

Several ways to decorate

DTF gives full colour and fine detail, flex gives crisp one-colour lettering, embroidery gives a raised logo

How to apply a logo

 
 
Prepare the transfer
A DTF transfer or cut flex; for the initial paper fit, use up to 10 × 5.5 cm; place the bottom of the design 1–1.5 cm above the visor seam.
 
Heat the press
Fit the cap platen and use the settings in the film instructions; 150–160 °C for 10–15 s is only a starting reference. Wait until the press reaches the set temperature.
 
Put the cap on the form
Fold the sweatband out, pull the cap over the lower form with the visor towards you and fasten the hook-and-loop strap: the front must sit tight, without folds.
 
Pre-press the front
Follow the chosen film's pre-press instructions and check how the fabric responds on a test cap.
 
Place the transfer
In the centre of the front, symmetrically to the seam; tack the edges with heat tape if needed.
 
Key step
Press
Use the temperature, time and pressure specified in the chosen film's instructions.
 
Peel the film
Hot or after cooling — as stated for your film.
 
Cool the cap
Let the cap cool completely, front up, before packing.
Tip: Test the first piece; peel according to the film instructions and check adhesion around every edge, especially on both sides of the centre seam. Note the setting that worked; change one setting at a time.

Vintage caps: which to choose

 
VariantFeatureHead sizeStrap
Vintage mesh cap with elastic, burgundyYou are herewear and small rips, mesh at the back56 cmhook-and-loop
Vintage six-panel mesh cap, burgundylight beige mesh at the back56 cmmetal buckle
Vintage six-panel cap, burgundyclassic cut56 cmmetal buckle

Where it works best

 
Studio or gym merch
A logo cap for coaches and clients that is comfortable with tied-up hair
Team and event
Caps of one cut in different colours for a run, hike or festival
Personal gift
Lettering, initials or a date on the front

What can go wrong

 
The design lifts at an edge

Cause: possible uneven contact beside the seam, unsuitable settings or an incorrect peel method

Fix: check contact on both sides of the seam, the transfer's suitability for cotton and its application instructions; make a fresh test after correcting the cause
A stripe below the design

Cause: the sweatband stayed under the front

Fix: fold the sweatband out before pressing
The design is crooked

Cause: the cap sat askew on the form

Fix: straighten the cap on the form: the front seam in the middle of the heater
A shiny mark from the heater

Cause: possible overheating or a pressure mark

Fix: check temperature, time, pressure and surface protection against the film instructions; if overheating is confirmed, reduce one setting within the permitted limits on a fresh test cap

Questions and answers

 

Can I print it with sublimation?

No: sublimation ink bonds with polyester, and this cap's front is cotton. For sublimation, choose a trucker cap with a white polyester front.

How do I apply a logo?

With a DTF transfer or flex on a cap press, or embroider it. DTF gives full colour, flex gives one-colour lettering and numbers.

What design size should I choose?

As a trial guide, use up to 10 × 5.5 cm or a round emblem up to 6 cm. Check the final size on the cap fitted to the press: the whole design must sit within the area of even contact.

What size is the cap?

Head circumference 56 cm, an adult size; a hook-and-loop strap at the back adjusts the fit.

What you need

 

A press and materials for applying a logo.

Характеристики Vintage Cotton Heat Six Blade Cap with Mesh and Elastic Frayed maroon (10318)

Customer reviews  (0)Leave a review
Customer reviews  (0)

You have already rated this product