Six-piece cap cotton black with black mesh (10323) - фото 1 - Blanks for sublimation
Top sellers
Six-piece cap cotton black with black mesh (10323) - фото 2 - Blanks for sublimation
Top sellers
Six-piece cap cotton black with black mesh (10323) - фото 3 - Blanks for sublimation
Top sellers
  • Six-piece cap cotton black with black mesh (10323) - фото 1 - Blanks for sublimation
  • Six-piece cap cotton black with black mesh (10323) - фото 2 - Blanks for sublimation
  • Six-piece cap cotton black with black mesh (10323) - фото 3 - Blanks for sublimation
  • Six-piece cap cotton black with black mesh (10323) - фото 1 - Blanks for sublimation
  • Six-piece cap cotton black with black mesh (10323) - фото 2 - Blanks for sublimation
  • Six-piece cap cotton black with black mesh (10323) - фото 3 - Blanks for sublimation

Six-piece cap cotton black with black mesh (10323)

(0)
In stock
Price:
229.00 грн
Product in cart
  • The date of shipment of the goods: tomorrow (23.11.2026)
  • Ask a question for this product

Payment Cash, Visa/MasterCard, Payment in installments, Instant installments, Cashless settlement.
Delivery By new mail to the branch, post machine or courier at carrier rates.

  • Return guarantee

    We guarantee a refund if you are not satisfied with the product

  • Доставка

    Delivery across Ukraine to any settlement

Description Six-piece cap cotton black with black mesh (10323)

Six-panel cap with a cotton front and mesh for DTF, flex and embroidery

 

A six-panel cap: the two front panels are cotton with a seam down the middle, the rest are mesh, and a plastic snap strap sits at the back. The logo goes on the front with a DTF transfer or flex on a cap heat press, or is embroidered.

Cotton fronttwo panels with a centre seam
Meshon the other panels
56 cmhead size
Plastic snap strapadjusts the fit at the back

Is this cap right for you

 
You apply DTF transfers, flex or embroidery
You have a cap heat press or a cap platen
The front has a centre seam: the transfer must lie tight on both sides of it — check on a test cap
You print with sublimation — choose a trucker cap with a white polyester front

Sizes and transfer settings

 
up to 10 × 5.5 cmtrial guide; check the design against the cap and platen
1–1.5 cmfrom the visor seam to the design
contact near the seamthe seam may hinder bonding; check on a test
Temperature
150–160 °Creference for DTF and flex
Time
10–15 sfollow the film manufacturer's instructions
Pressure
mediumreference only; follow the film's pressure instructions

These are starting settings: the film maker gives the exact ones, and they are tuned to your press and room conditions — temperature and humidity.

Why this cap

 

Mesh panels

Mesh side and rear panels make the cap light and airy

Several decoration methods

DTF gives full colour and fine detail, flex gives crisp one-colour lettering, embroidery gives a raised logo

Colour combinations

The front and mesh come in different colour combinations, so the cap is easy to match to brand colours

How to apply a logo

 
 
Prepare the transfer
A DTF transfer or cut flex; for the initial paper fit, use up to 10 × 5.5 cm; place the bottom of the design 1–1.5 cm above the visor seam.
 
Heat the press
Fit the cap platen and use the settings in the film instructions; 150–160 °C for 10–15 s is only a starting reference. Wait until the press reaches the set temperature.
 
Fit the cap on the form
Fold the sweatband outwards, pull the cap onto the lower form with the visor towards you and fasten the snap strap: the front must sit tight, without folds.
 
Pre-press the front
Follow the chosen film's pre-press instructions and check how the fabric responds on a test cap.
 
Place the transfer
In the centre of the front, symmetrically to the seam; tack the edges with heat tape if needed.
 
Key step
Press
Use the temperature, time and pressure specified in the chosen film's instructions.
 
Peel the film
Hot or after cooling — as stated for your film.
 
Cool the cap
Let the cap cool completely, front up, before packing.
Tip: Test the first piece; peel according to the film instructions and check adhesion around every edge, especially on both sides of the centre seam. Note the setting that worked; change one setting at a time.

Mesh caps: which to choose

 
VariantFeatureHead sizeStrap
Six-panel mesh cap, black with black meshYou are herecotton front with a seam56 cmplastic snap
Cotton five-panel mesh cap, blackmesh side and rear panels56 cmplastic snap
Trucker cap, blackcoloured front for DTF and flex56 cmplastic snap

Where it works best

 
Summer merch
A light mesh cap for a festival, camp or outdoor event
Team and event
Caps with a logo or number for a tournament, hike or festival
Promo and giveaways
Logo caps for an exhibition, campaign or corporate event

What can go wrong

 
The design lifts at an edge

Cause: possible uneven contact beside the seam, unsuitable settings or an incorrect peel method

Fix: check contact on both sides of the seam, the transfer's suitability for cotton and its application instructions; make a fresh test after correcting the cause
A stripe below the design

Cause: the sweatband stayed under the front

Fix: fold the sweatband out before pressing
The design is crooked

Cause: the cap sat askew on the form

Fix: straighten the cap on the form: the front seam in the middle of the heater
A shiny mark from the heater

Cause: possible overheating or a pressure mark

Fix: check temperature, time, pressure and surface protection against the film instructions; if overheating is confirmed, reduce one setting within the permitted limits on a fresh test cap

Questions and answers

 

Can I print it with sublimation?

No: sublimation ink bonds with polyester, and this cap's front is cotton. For sublimation, choose a trucker cap with a white polyester front.

What do I apply the logo with?

A DTF transfer or flex on a cap press, or embroidery. DTF gives full colour, flex gives one-colour lettering and numbers.

What design size should I choose?

As a trial guide, use up to 10 × 5.5 cm or a round emblem up to 6 cm. Check the final size on the cap fitted to the press: the whole design must sit within the area of even contact.

What size is the cap?

Head circumference 56 cm, an adult size; a plastic snap strap at the back adjusts the fit.

What you need

 

A press and materials for applying a logo.

Характеристики Six-piece cap cotton black with black mesh (10323)

Customer reviews  (0)Leave a review
Customer reviews  (0)

You have already rated this product