Five-blade cap with mesh cotton, gray (10358) - фото 1 - Blanks for sublimation
Five-blade cap with mesh cotton, gray (10358) - фото 2 - Blanks for sublimation
Five-blade cap with mesh cotton, gray (10358) - фото 3 - Blanks for sublimation
  • Five-blade cap with mesh cotton, gray (10358) - фото 1 - Blanks for sublimation
  • Five-blade cap with mesh cotton, gray (10358) - фото 2 - Blanks for sublimation
  • Five-blade cap with mesh cotton, gray (10358) - фото 3 - Blanks for sublimation
  • Five-blade cap with mesh cotton, gray (10358) - фото 1 - Blanks for sublimation
  • Five-blade cap with mesh cotton, gray (10358) - фото 2 - Blanks for sublimation
  • Five-blade cap with mesh cotton, gray (10358) - фото 3 - Blanks for sublimation

Five-blade cap with mesh cotton, gray (10358)

(0)
Color: Gray
In stock
Price:
119.00 грн
Product in cart
  • The date of shipment of the goods: 2026-11-23
  • Ask a question for this product

Payment Cash, Visa/MasterCard, Payment in installments, Instant installments, Cashless settlement.
Delivery By new mail to the branch, post machine or courier at carrier rates.

  • Return guarantee

    We guarantee a refund if you are not satisfied with the product

  • Доставка

    Delivery across Ukraine to any settlement

Description Five-blade cap with mesh cotton, gray (10358)

Five-panel cap with a cotton front and mesh panels

 

The logo goes on the front with a DTF transfer or flex on a cap heat press, or is embroidered.

Cotton frontfor DTF, flex and embroidery
Meshon the side and rear panels
56 cmhead size
Plastic snap strapadjusts the fit at the back

Is this cap right for you

 
You apply DTF transfers, flex or embroidery
You have a cap heat press or a cap platen
The design goes on the cotton front; use the settings in the chosen film's instructions
You print with sublimation — choose a trucker cap with a white polyester front

Sizes and transfer settings

 
up to 10 × 5.5 cmtrial guide; check the design against the cap and platen
1–1.5 cmfrom the visor seam to the design
Temperature
150–160 °Creference for DTF and flex
Time
10–15 sfollow the film manufacturer's instructions
Pressure
mediumreference only; follow the film's pressure instructions

These are starting settings: the film maker gives the exact ones, and they are tuned to your press and room conditions — temperature and humidity.

Why this cap

 

Mesh panels

Mesh side and rear panels make the cap light and airy

Seamless front

A centred logo does not cross a seam

Several decoration methods

DTF gives full colour and fine detail, flex gives crisp one-colour lettering, embroidery gives a raised logo

How to apply a logo

 
 
Prepare the transfer
A DTF transfer or cut flex; for the initial paper fit, use up to 10 × 5.5 cm; place the bottom of the design 1–1.5 cm above the visor seam.
 
Heat the press
Fit the cap platen and use the settings in the film instructions; 150–160 °C for 10–15 s is only a starting reference. Wait until the press reaches the set temperature.
 
Fit the cap on the form
Fold the sweatband outwards, pull the cap onto the lower form with the visor towards you and fasten the snap strap: the front must sit tight, without folds.
 
Pre-press the front
Follow the chosen film's pre-press guidance and check how the fabric responds on a test cap.
 
Place the transfer
In the centre of the front; tack the edges with heat tape if needed.
 
Key step
Press
Use the temperature, time and pressure specified in the chosen film's instructions.
 
Peel the film
Hot or after cooling — as stated for your film.
 
Cool the cap
Let the cap cool completely, front up, before packing.
Tip: Test the first cap of each batch; after peeling the film as stated for it, check that every edge of the design has bonded. Record the settings that worked; change one setting at a time.

Cotton caps: which to choose

 
VariantFeatureHead sizeStrap
Cotton five-panel mesh cap, greyYou are heremesh side and rear panels56 cmplastic snap
Cotton five-panel cap, greysolid fabric56 cmhook-and-loop
Vintage six-panel mesh cap, light greywashed cotton, mesh at the back56 cmmetal buckle

Where it works best

 
Summer merch
A light mesh cap for a festival, camp or outdoor event
Team and event
Caps with a logo or number for a tournament, hike or festival
Promo and giveaways
Logo caps for an exhibition, campaign or corporate event

What can go wrong

 
The edge of the design lifts

Cause: possible uneven contact, unsuitable settings or peel method

Fix: check contact across the whole design, the transfer's suitability for cotton and its application instructions; after correcting the cause, make a new test
A band under the design

Cause: the sweatband stayed under the front

Fix: fold the sweatband outwards before pressing
The design is crooked

Cause: the cap sat on the form at an angle

Fix: straighten the cap on the form: the centre of the front goes in the middle of the heater
A shiny mark from the heater

Cause: possible overheating or a pressure mark

Fix: check the temperature, time, pressure and surface protection against the film instructions; if overheating is confirmed, reduce one setting within the permitted range on a fresh test cap

Questions and answers

 

Can I print it with sublimation?

No: sublimation ink bonds with polyester, and this cap's front is cotton. For sublimation, choose a trucker cap with a white polyester front.

What do I apply the logo with?

A DTF transfer or flex on a cap press, or embroidery. DTF gives full colour, flex gives one-colour lettering and numbers.

What design size should I choose?

As a trial guide, use up to 10 × 5.5 cm or a round emblem up to 6 cm. Check the final size on the cap fitted to the press: the whole design must sit within the area of even contact.

What size is the cap?

Head circumference 56 cm, an adult size; a plastic snap strap at the back adjusts the fit.

What you need

 

A press and materials for applying a logo.

Характеристики Five-blade cap with mesh cotton, gray (10358)

Customer reviews  (0)Leave a review
Customer reviews  (0)

You have already rated this product