A tear-off coupon needs to stay attached during production and separate when the user tears it. Short uncut ties between through-cuts make that possible. Tooth count alone is not enough: what matters is how much paper remains intact and whether the cuts go all the way through.
Check the cuts first. If the paper is still connected within them, correct the operation. If the cuts go through, compare geometry on the same paper: test smaller ties if tearing is too difficult, or larger ties if the coupon separates too soon.
What holds the coupon together
Perforation alternates cuts, where the paper is cut all the way through, with uncut ties, where it remains intact. The ties connect the main and detachable sections of the same sheet. As the coupon is torn along the line, these ties break one after another.
Printed dotted line
Ink dots sit on the surface. The paper beneath them remains intact.
Crease
A continuous indentation prepares the fold. The paper stays connected along the entire line.
Perforation
Through-cuts alternate with uncut ties. Each blue tie joins the upper and lower parts of the sheet.
Top view. Blue is paper; grey within the cuts is an opening. Cut openings and crease relief are exaggerated for clarity.
A continuous cut separates the sections immediately. A printed dotted line only marks a route, while a crease prepares a fold. To make a tear line, choose a model with a confirmed perforating function from the creasing and perforating equipment category. A creasing function alone does not provide perforation.
The same repeat, different ties
Full repeat = cut + uncut tie. Having the same number of repeats over a given length therefore does not fully describe the connection between the sections.
Consider a teaching example: both variants have a 2 mm full repeat. Along a 50 mm line, we count 25 full repeats. The paper and grain direction are the same, and every cut goes all the way through.
A · Full repeat 2 mm
B · Full repeat 2 mm
One full repeat per variant, at the same scale along the line. Each tie is the same paper joining the two sections. The cut opening is exaggerated. Teaching geometry, not a blade drawing.
A: 25 × 0.5 mm = 12.5 mm of ties along the line.
B: 25 × 0.2 mm = 5 mm of ties along the line.
| Along a 50 mm line | A | B |
|---|---|---|
| Full repeats | 25 | 25 |
| Total tie length | 12.5 mm | 5 mm |
| Uncut share of the line | 25% | 10% |
B is worth testing when an easier tear is needed, because it leaves less intact paper along the line. A leaves more connection. These lengths and percentages describe geometry, not tear force. They cannot be used to calculate force proportionally or to declare B the better option in advance.
Tooth count is useful alongside the cut and tie lengths of the particular tool. Neither “more teeth means easier tearing” nor the reverse applies to every type of perforation.
Incomplete cuts or unsuitable geometry?
Inspect the sample from both sides, using magnification if needed. At each intended cut, the paper should be cut all the way through. A tooth mark alone does not confirm this. The edges of a complete cut may touch each other; the openings in the diagrams are deliberately spread for clarity.
Intact paper remains within the cuts
The operation is incomplete. Check that the fitted tool is a perforating tool, inspect its condition and check its permitted settings, then make a fresh sample. Indentations leave an extra connection where a through-cut was intended.
A pressure adjustment provided by the manufacturer may help the tool cut all the way through. Pressure does not create a different pattern of teeth and gaps. If a different geometry is needed, first establish which suitable tooling is compatible with your equipment.
The cuts are complete, but tearing is too difficult
Compare an available, compatible geometry with smaller ties on identical blanks. Keep the paper, grain direction and subsequent processing unchanged so you can understand the effect of this change.
The cuts are complete, but the coupon separates too soon
Test a variant with larger ties and note the stage at which the current sample breaks. A coupon that is intact immediately after perforating may still separate during later feeding, cutting, folding or packing.
Test the whole route before tearing
- Prepare identical printed blanks. Compare available geometries on the same paper, in the same format and with the same grain direction. Make sure the cuts in both samples are complete.
- Put the samples through the actual production route. They need to survive feeding and every subsequent operation the job requires: cutting, folding, packing and ordinary handling before use. Note when any damage starts.
- Then tear off the intended section. Use the normal motion a user would make. Check whether separation follows the line and preserves the area of the coupon that needs to remain intact. Keep a labelled sample that survived processing and separated along the intended line.
Paper thickness, coating and grain direction also affect tearing. If neither sample is suitable, change one condition — geometry, material or how the operation is performed — and test again. The teaching example concerns ordinary homogeneous paper; laminated, self-adhesive, synthetic and multilayer materials need a separate assessment.
An easier tear is useful only if the coupon stays intact until then. If the ties break during processing, that is premature separation, even when the edge looks neat.
