To stop a design transferring to the back of a polyester shirt, put a fresh sheet of protective paper the size of the platen between the front and back: the top sheet only protects the platen. If you print both sides, pull the paper out right after the first press and let the shirt cool. Press the second side with the shirt pulled over the lower platen or with a pillow wrapped in clean paper inside.
Is the back stained, or is the front just showing through?
Put a clean, opaque white sheet inside the shirt and inspect the back. If the design disappears, the back is clean: you were seeing the front through thin fabric. If a copy remains, the dye has transferred to the back.
Why the back gets stained
Heat transfers dye from sublimation paper into polyester. Some dye can pass through thin fabric. Most gets through under dense dark fills, through thin sports knit, and when the press is too hot or the time too long. When a shirt lies flat in a heat press, its back sits directly beneath the front and can take up colour too. The second layer of a pillowcase or fabric bag can be stained in the same way.
Where the inner sheet belongs
Cross-section: from upper to lower platen
Outer protection only
Protection between layers
The top and bottom sheets protect the press. The inner sheet separates the fabric layers.
How to lay out the paper
Use a new blank from the same batch and the same design. Keep your settings if the front comes out well: for a polyester shirt, usually 190–200 °C, 40–60 s and medium pressure. If you press hotter than 200 °C or longer than 60 s, come back into this range.
- Put sublimation protective paper inside: thin grey or brown uncoated paper, 30 g/m². The roll can be ordered cut to the width of your press. Clean, unprinted office paper also works. Do not use waxed paper, coloured craft paper or printed sheets.
- Lay the sheet flat inside the shirt. It must cover the design you are pressing with a 2 cm margin, and the print on the other side too if it is already printed. The simplest is a sheet the size of the platen: a 40 × 40 cm piece for a 38 × 38 cm platen. No folds, joins or paper edges under the design. Under a dense dark fill or thin knit, use two sheets.
- Put a clean sheet under the shirt and cover the transfer with another one, larger than the platen.
- Right after pressing, while the shirt is hot, peel the transfer and pull out the inner sheet. Then lay the shirt flat and let it cool: a hot sheet left inside gives dye back to the fabric.
Example: cutting the inner sheet
Protective paper: at least 24 × 29 cm
A 2 cm margin on every side
If you also print the other side, the sheet must cover that print too. The simplest is a sheet the size of the platen.
Colour on protective paper does not mean a failed print
The paper catches dye that passes through the fabric. After cooling, inspect both the paper and the back panel. Colour on the sheet is normal: that is what it is there for. The result shows on the back.
Do not turn a dirty sheet over to its 'clean side': under the press, the dye on it will transfer to the shirt again.
How to print the second side
Print the smaller or less important side first: it will lose a little colour in the second cycle. Paper catches dye but lets heat through. If the shirt lies flat, the finished print is heated again in the second cycle: it fades and gives dye to the layers next to it. So right after the first press, pull out all the sheets and let the shirt cool completely.
If the press heats only from the top and the shirt slides over the lower platen without stretching, pull it on: the side to print on top, the finished print hanging below the platen. Do this only with the upper platen fully open or swung away.
If it does not fit, put a Teflon pillow wrapped in fresh protective paper inside: it shields the finished print from some of the heat and pressure, and the paper keeps dye off the pillow. Put a new sheet under the shirt, below the finished print.
Before the run, make one shirt with both sides: once it cools, both prints should be bright, with no new stains.
If the back is already stained
Washing will not remove the stain: the dye is already in the polyester. Do not press the shirt again to 'pull out' the stain; the print you want will fade too. A faint copy can be hidden under a new design on the back if that design has a dense dark colour in that spot: sublimation is transparent, and light areas will not cover the stain. Use the rest of these shirts for test presses.
