Glossy laminate over the marks reflects light, so the cutting plotter cannot see them. Check this with an identical print without film: the plotter should read it. On the next sheets, apply cold laminating film only over the sticker area: it should extend 3 mm past the cut lines and stop at least 1 cm short of the marks.
Why you can see the mark but the plotter cannot
The plotter uses the black marks to find where the artwork sits on the sheet and to lay the cut path from the file over it. A camera or optical sensor looks for them. Glossy film reflects light straight back into the camera or sensor, and the black mark blends into the white background.
A new blade or more cutting force will not help here: the plotter stops before it starts cutting.
Cross-section through a mark
Mark under laminate
Glare
Uncovered mark
Under gloss the mark glares; left uncovered on matte film, it keeps its contrast.
Compare with an unlaminated sheet
Take the problem sheet and an identical print on the same film without laminate. The file, the marks and the edge you feed into the plotter first must match. Print at 100% scale, without fitting to the page.
Inspect the print itself: every mark must be complete and sharp, without gaps, smeared ink or edges clipped by the printer. Reprint a blurred or clipped mark: moving the sheet in the plotter will not fix it.
Draw the blind and turn away any lamp that puts glare on the sheet. The material should lie flat, without ripples. Compare mark reading under the same lighting. If the plotter cannot see the marks on the unlaminated sheet either, print the same file on plain white office paper.
| What happened | What to do next |
|---|---|
| Reads without laminate; fails or reads only sometimes with it | The laminate is the problem. Laminate only the sticker area on the next sheet, as shown below. If the sheet has curled, feed it on a plotter carrier mat, and apply the film without stretching it on the next sheets. |
| Reads paper, not the film | The base itself is the problem: glossy, silver or clear. Print on matte white film, as shown below. |
| Cannot read even paper | Laminate and film are not the cause. Add the marks again in your plotter software, print at 100% scale and insert the sheet by the edge the software shows. If that does not help, call the MyPrint technical department (number at the bottom of the page): give the plotter model and the software, and keep the file and a photo of the sheet with marks at hand. |
How to keep the stickers glossy
Print on a matte white base and add gloss with film only over the stickers: on a glossy base the mark will glare even without laminate. Use MyPrint matte white polypropylene self-adhesive inkjet film in A4 or A3. It is made for water-based (dye) ink or a laser printer. If all the inks in your printer are pigment, use matte self-adhesive photo paper.
- Add the marks only in the software you cut with (for most MyPrint plotters that is SignMaster), with your plotter selected in it. The software sets the mark shape and size itself: do not draw or rescale them by hand. Keep artwork and borders away from the marks; if the software hatches a restricted zone, leave all of it empty.
- Trim the laminating film before applying it. It should extend 3 mm past the outer cut lines and stop at least 1 cm short of the marks. Not enough room? Increase the mark offset from the layout in the software, or rearrange the stickers. Keep matte, holographic and textured film off the marks too: marks under matte film do not always read, and holographic film reflects even more.
- Apply the film to the dry print: peel the liner off gradually and smooth from the stuck edge to the opposite one. Do not stretch the film: stretched film curls the sheet later. Load the sheet the same way as the control sample.
- Cut the first sheet on its own and check that the cut follows the artwork at the start and at the end of the sheet. Only then cut the batch.
Where the laminate ends
Marks under film: not read
Film covers the whole sheet
Marks left bare: read
Film covers only the stickers
Blue is the laminating film: it extends 3 mm past the cut lines and stops at least 1 cm short of the marks.
If the sheet is already laminated
Put a small piece of matte clear tape over each mark: the “invisible” office kind, not glossy. It kills the glare, and the mark shows through it. Do not trace the marks with a marker: an inexact line shifts the cut. If the plotter still cannot see the marks, reprint the sheet and laminate it as shown above.
