22.05.2026

Plastic coil unwinding from a notebook: why both ends need crimping

Plastic coil unwinding from a notebook: why both ends need crimping

To keep a continuous plastic coil from winding back out of a notebook, finish both ends after insertion: remove the surplus and form an inward bend, toward the book. A neat, short cut only shortens the coil; it does not create a retaining stop.

When choosing a binding in the binding supplies category, select the plastic-coil type. Each turn continues into the next as one continuous strand. A plastic comb has a spine and separate teeth, while Wire-O has paired metal loops. Those bindings use different opening or closing methods.

Why a neat cut is not enough

During insertion, the coil rotates and its end passes through the holes in sequence. Without a retaining stop, the reverse route remains open: the coil can rotate back and its free end can work out of the end holes. An inward bend obstructs that reverse passage. A continuous coil has two free ends, so both need finishing.

Our hypothetical example is one work notebook. The coil pitch matches the punched holes, all sheets and both covers are in place, and they already turn freely. Compare the notebook after insertion, after a simple trim and after proper finishing.

1. Coil inserted

Notes

Surplus coil still extends beyond both ends.

2. Cut only

Notes

The ends are shorter, with no inward bends.

3. Both ends finished

Notes

Each end has a bend facing the book.

All three views show the same notebook, with the binding at the top. The blue line represents one continuous coil; the pale sections show its continuation behind the book. The number of turns is illustrative, and the orange circles mark the end holes.

A retaining bend at each end

In the finished version, each tip faces toward the book. At the left end, that means rightward; at the right end, leftward. The bend forms a stop at the coil end while the end hole still contains a turn of the coil.

Left end

Notes

Bend toward the book →

The end hole still contains the coil.

Right end

Notes

← Bend toward the book

The end hole still contains the coil.

These are enlarged details of the same finished notebook. The arrows explain the inward bend direction, not the movement or orientation of the pliers. The projection is simplified for clarity; the shape and size on screen do not specify a tail length or tool setting.

Finish one end, turn the book, finish the other

Use plastic-coil cutting and crimping pliers, or a suitable coil crimper, rated for the coil diameter. Ordinary cutters that only cut may leave a neat tip without the required retaining bend.

  1. Check the complete book. The coil must pass through every hole in the sheets and both covers, including the end holes. Leave enough coil projecting at each end for your finishing tool. Do not trim it flush with the edge beforehand.
  2. Finish the first end. Support the book and engage the tool around the end section emerging beyond its edge. Suitable pliers cut off the surplus and form a bend toward the book in the same operation. Follow the instructions for those particular pliers when positioning their jaws. Inspect the tip afterwards: look for a visible inward bend, not just a short cut.
  3. Turn the book over and finish the second end. Position the opposite coil end where you can reach it comfortably, then repeat the operation. One finished bend does not replace the other.
  4. Check page turning. Inspect both bends and both end holes: the coil must remain in the holes. Turn the front and back covers, the outer sheets and the sheets within the book. They should move freely without snagging on the coil ends. If a tip catches the material, correct it with the appropriate tool and check again.

Already cut the end too short?

If too little of the end remains to form the proper bend, replace the coil with a compatible one of sufficient length. Insert it through all the holes again and finish both ends. Do not keep trimming inside the last hole: it needs to retain the sheets, not be left empty.

A larger diameter alone will not restrain an unbent end. If both retaining stops are present but the sheets are tight or the holes damaged, separately check the pitch match, the diameter against the complete book thickness, and the condition of the punched holes. Finishing the ends does not correct those problems.