27.05.2025

Pale patches after sublimation: pre-press the fabric first

Pale patches after sublimation: pre-press the fabric first

The colour is even on the paper, but the polyester comes out of the press with pale, cloudy patches: this is often steam from damp fabric or paper. Before every transfer, pre-press the item in the flatbed heat press for 3–5 seconds without the print (up to 10 for dense sports knit), lift the platen to let the steam out, and only then lay the dry print under a fresh sheet of protective paper, not a PTFE sheet. If the pale patch lands in the same place on the platen every time, the press is to blame, not moisture.

What causes pale, cloudy areas?

In a hot press, excess moisture in the fabric or paper turns to steam. It pushes some of the dye aside: solid areas come out patchy, and colour sometimes spreads beyond the outline.

What happens between the paper and fabric

Moisture during transfer

Paper · printed side down
↓← steam →↓

Fabric: less dye in some areas

Dry, flat fabric

Paper · printed side down
↓↓↓↓

Fabric: even dye transfer

Steam pushes the dye aside and leaves a pale patch on the fabric.

Wrinkles, seams, light pressure and cooler spots on the platen leave the same patches. So run the test on a flat, seamless offcut without changing the settings.

Compare two offcuts

Before you pre-press a whole batch this way, check it on two offcuts. Dry wet fabric fully first: pre-pressing removes only residual moisture. If you already pre-press every item, go straight to the paper check.

Take two matching offcuts of the same fabric and print two fresh, identical solid-colour rectangles on sublimation paper. The colour must be even on the paper, and the prints dry.

  1. Remove lint and lay the fabric flat. The whole design must sit under the platen, with no wrinkles or seams beneath it.
  2. Keep your usual preparation for one offcut; pre-press the other without the print for 3–5 s (up to 10 s for dense knit) at the transfer temperature. Polyester T-shirts are usually pressed at 190–200 °C for 40–60 s at medium pressure. If your paper or fabric maker gives its own settings, use those.
  3. Lift the platen and let the second offcut cool for a few seconds so the steam escapes. On hot fabric, dye can start to transfer while you are still aligning the sheet.
  4. Transfer both prints in turn in the same area of the press. Do not change the time, temperature, pressure or the way the print is held. Use a new sheet of protective paper for every pressing. Compare the offcuts once they cool, under the same light.

Offcut 1

Usual preparation → transfer

Offcut 2

Pre-press → cool → transfer

Same fabric, print, dry paper, press area and transfer settings. Only pre-pressing changes.

If the second offcut is more even, repeat its preparation on one more. If the repeat is even too, pre-press every item in the batch this way.

Fabric pre-pressed? Check the paper

Keep paper in a closed pack in a dry place. If the pack may have taken on moisture, print the test on a sheet from a new sealed pack, without changing the pre-press or the settings. Let a fresh print with heavy solid areas dry for 2–3 minutes.

Cover the print with sublimation protective paper: thin uncoated paper soaks up moisture and excess dye. The roll can be ordered cut to the width of your press; for a small print, clean unprinted office paper also works. The top sheet should extend beyond the print on all sides; put another sheet inside the T-shirt so colour does not reach the back. Use a fresh sheet for every transfer: a used one passes dye to the next item.

PTFE sheets, baking parchment and waxed paper do not absorb moisture, so put paper, not PTFE, directly over the print.

If the patches remain

What you seeNext action
A patch beside a seam, collar or wrinklePut a heat press pillow under the print area so the seam sits beyond its edge. Smooth out wrinkles with the pre-press.
A pale area repeats in the same platen zoneCheck heat-press contact and heating uniformity.
Patches move from item to item; pre-pressing and dry paper did not helpIncrease the pressure: T-shirts need medium pressure, and the print must sit firmly against the fabric everywhere. Then repeat the test.
The whole image is uniformly paleCheck the fabric composition: it needs at least 65 % polyester, and 100 % gives the brightest colour. Then check that you printed on the coated side of the paper and that the settings are not below 190 °C and 40 s.

Re-pressing will not save a finished item: the colour fades further and the polyester picks up a platen mark. Get the pre-press right on an offcut, then print the next item.