24.09.2026

Pale band at the bottom of a sublimated mug: the mug or the press?

Pale band at the bottom of a sublimated mug: the mug or the press?

A pale band at the bottom of a mug means the edge of the design next to the base got too little heat or contact. The thick base warms up more slowly, and the heater sits less tightly against a tapered wall. To find out which it is, on a fully warmed press put a new mug in the other way round, with the base where the rim was. If the band is at the base again, the mug is the cause. If it has moved to the rim, look at the heater.

Why the bottom goes pale

A mug press heats only the side wall. The base is usually thicker than the wall, and the heater never touches it. While the wall heats up, part of the heat flows into the base, so the band just above it stays cooler for longer. Less dye transfers there.

The second cause is taper. Many mugs are slightly narrower at the bottom so that they release from the mould. The heater is straight, so near the base the paper sits looser and the ink transfers weakly or in patches.

The third is a cold start. A cold mug absorbs a lot of heat: after it goes in, the display can drop by 15 °C or more. That is why the first mugs after switching on or after a break most often come out with a pale bottom.

1. The base soaks up heat

The heater warms the wall, the ink transfers fully

← Pale band: heat flows into the base

Base: the thickest ceramic

2. A tapered mug pulls away from the heater

The heater is straight

At the top the paper is pressed tight

At the bottom a gap between heater and mug: less contact and heat

heaterpaperdesign on the mugpale bandceramic

Cross-section diagram. Wall thickness and taper are exaggerated so you can see them.

Compare two mug positions

First rule out a cold start: once the press reaches temperature, give it another 10–15 minutes and press one mug in the usual position. If the band is gone, the cold press was the cause. If it is still there, take an identical new mug and the same design, and put it in the other way round, base on the other side. Keep time, temperature and pressure the same.

1. Mug in the usual position

baserim

Pale band next to the base.

2. New mug, base on the other side

rimbase

The band is at the base again.

The mug is the cause: thick base or taper

rimbase

The band stayed on the same side of the press and is now at the rim.

The press is the cause: this edge of the heater heats or presses less

If the band stayed at the base, stand the cold mug on the table and hold a square or ruler upright against its side. A gap at the bottom means the mug tapers, and warming alone will not remove the band.

Band at the base again: what to change

1 min

Warm the base

Let mugs from a cold store reach room temperature first. Then pour hot water from a kettle into the mug for a minute, empty it away from the press and dry it thoroughly inside and out: a drop of water under the paper leaves a spot.

5 mm

Keep away from the edge

Leave 5 mm from the bottom of the straight part and the same from the rim. Do not count the rounded edge at the base.

no overhang

Trim and fix the paper

Paper that hangs over the edge of the mug creases and leaves white lines. Wrap it tight and fix it with heat tape at the top and bottom.

+10–15 s

Add time, not degrees

A white 330 ml mug is usually pressed at 180–200 °C for 180–230 s; for the AP1803 press it is 200 °C and 180 s. Check your press manual for both the settings and when the timer starts: as soon as the press closes, or once the temperature has recovered. Add time in steps of 10–15 seconds on a new mug and change one thing at a time. If the middle is already fully saturated, do not raise the temperature: the middle will blur and turn brownish before the bottom is done.

taper

Match the heater or the mug

Conical latte mugs are pressed with a conical heating element. If it is an ordinary mug and the gap under the ruler is small, check the pressure first (below). If that does not help, use straight-sided sublimation mugs; check the shape and diameter on the product card.

Band moved to the rim: check the press

Pressure
With a mug inside, the press handle closes with noticeable effort but with one hand. If it closes easily, turn the adjusting screw a quarter turn and press another mug. Do not overtighten: you can damage the mechanism or crack the mug.
Heating element
Switch the press off, let it cool and inspect the heater. Dents, cuts or a sagging edge that match the pale areas on the print mean the pad or the heating element needs replacing; do not work with a damaged heater. The standard element for the MP160 is 12 × 23.5 cm and fits mugs 7.5–9 cm in diameter; the MP560 standard element is different, 11.5 × 22.5 cm.
Size
425 ml mugs have a larger 15 × 25 cm heating element, and the small and large conical ones for latte mugs come in the MP160 and AP1803 5-in-1 sets. Before buying, check your press model and the mug size.

If more than the bottom goes pale

The diagrams show the unrolled design: rim at the top, base at the bottom, the areas next to the handle at the sides.

Bands at the bottom and top

The design runs onto the rounded edges, or the paper overhangs.

→ Keep 5 mm margins, with the paper within the straight part of the wall.

Pale edges next to the handle

The heater does not wrap around there, and the handle draws heat.

→ Keep the design at least 1.3 cm from the handle.

A spot in the same place every time

Probably wear in the heater at that spot.

→ With the press off and cold, inspect that area; replace a damaged pad or heating element.

The whole design is pale

Too little time or temperature, or a weak print.

→ Check the press settings and the print itself.