09.05.2025

Numbered tickets: assembling cut piles in order

Numbered tickets: assembling cut piles in order

To assemble numbered tickets in order after cutting, the numbers must run consecutively down through the stack at each position. With five sheets and four tickets per sheet, the first sheet carries 1, 6, 11, 16. After cutting, pile A goes above B, B above C, and C above D.

Cutting separates the same position on every sheet. If you number across each sheet — 1–4 on the first, then 5–8 — the numbers in the first cut pile increase by four.

First pile A · top to bottom

Numbering across each sheet

1 · 5 · 9 · 13 · 17

Numbering through the stack

1 · 2 · 3 · 4 · 5

Five sheets: where every number belongs

Hypothetical example: 20 single-sided tickets, four positions A–D. A is top left, B top right, C bottom left, and D bottom right. All five sheets lie face up, with sheet 1 on top and sheet 5 at the bottom; their top edges point the same way.

Sheet 1 · on top

↑ Top edge · printed face

A1
B6
C11
D16

Sheet 5 · at the bottom

↑ Top edge · printed face

A5
B10
C15
D20

Position diagram; dimensions, margins and bleed are not shown.

All five sheets · top to bottom

Sheet ↓ABCD
1161116
2271217
3381318
4491419
55101520

Each table row represents a whole sheet; each column A–D becomes a cut pile. Number 8, for example, is at position B on sheet 3: after cutting, it will be third from the top in pile B.

One data row becomes one printed sheet

Create four fields A, B, C and D in a spreadsheet and fill them as shown. In the layout containing four tickets, bind field A to the number on the top-left ticket, B to the top-right, C to the bottom-left, and D to the bottom-right. If your layout editor supports data merging, output each data row as one page the size of the printing sheet: it already contains all four tickets.

For a different starting number or group size, use:

n = n₀ + (p − 1) × S + (s − 1)

n₀ is the starting number; p is the position number (A = 1, B = 2, C = 3, D = 4); S is the number of sheets in the group you will assemble together; s is the sheet number counted from the top, from 1 to S.

For B on sheet 3: 1 + (2 − 1) × 5 + (3 − 1) = 8.

If you need 18 tickets: you still have five sheets and 20 slots, so S = 5. Leave the D fields on sheets 4 and 5 empty instead of printing 19 and 20; set those two unnumbered pieces aside after cutting. Do not fill them with repeated valid numbers. If the design calls for 0001 instead of 1, preserve the leading zeros during the merge.

Before printing, check the first sheet, 1 / 6 / 11 / 16, and the last, 5 / 10 / 15 / 20. Each finished page is already a sheet layout: placing several of these pages on another sheet, or applying another cut-stack rearrangement, will change the intended order.

From printed sheets to one stack

Numbering needs no special paper: for ordinary tickets, choose stock suitable for your printer. If you want a photo coating for colourful inkjet-printed certificates, compare inkjet photo paper by surface finish and by the sheet sizes and thicknesses your printer accepts.

  1. Put the actual output in order. Arrange the sheets face up, 1, 2, 3, 4, 5 from top to bottom, with their top edges pointing the same way. The table does not determine which face is up or the order in which your printer delivers sheets. If sheet 5 is on top, restore the order before cutting while keeping the printed faces up.
  2. Replace a spoiled sheet in its original position. A reprint of sheet 3 carries the same 3, 8, 13, 18. Remove the old sheet from the working batch and put the replacement third from the top. If the old sheet has already been cut, remove all four of its tickets, including usable ones, before replacing the whole sheet: the finished batch must contain only one copy of each number.
  3. Separate the positions. Following the agreed cutting layout, separate the top pair A/B from the bottom pair C/D, then A from B and C from D. Keep the sheet order within every pile. Before assembly, return all piles to the same orientation: numbers visible and ticket tops pointing the same way. Turning a pile face down reverses the order inside it.
  4. Build from the bottom up: keep D at the bottom, put C on D, then B, and A last. Move whole piles without changing the ticket order inside them. The finished stack will then read 1…20 from top to bottom.

After cutting: four piles

Read down each pile from the top ↓

A

1

2

3

4

5

B

6

7

8

9

10

C

11

12

13

14

15

D

16

17

18

19

20

Each pile keeps sheets 1–5 in their original order. Letters and colours identify the same positions as in the table.

One assembled stack

D at the bottom → C on D → then B → A on top. The numbers below run from top to bottom.

Top ↓

A
12345
B
678910
C
1112131415
D
1617181920

Bottom

When choosing equipment, compare paper cutters by sheet format and permitted stack thickness for your stock. Five sheets is an assumption in this calculation; whether they can be cut together depends on the particular cutter.

If printing or cutting is split into parts

S belongs to the assembly group. It does not automatically become the number of sheets in each separate feed or cutting batch. Choose one of these two methods before preparing the numbers:

  • Keep the table for all five sheets. For example, split them into sheets 1–3 and sheets 4–5. After cutting, place A from the first part (1, 2, 3) above A from the second (4, 5); combine B, C and D in the same way. Only then put the complete A above B above C above D. If you immediately assemble each part as a separate finished stack, number 3 will be followed by 6.
  • Calculate two complete groups. For the first, use S = 3 and start at 1: its first sheet is 1 / 4 / 7 / 10, and its assembled result is 1…12. For the second, use S = 2 and start at 13: its first sheet is 13 / 15 / 17 / 19, yielding 13…20. Put the finished first group above the second. This method requires recalculating the layout for each group in advance.

Before the print run, copy the main table in pencil onto five small paper rectangles, marking the top edge and sheet number. Separate them along the position boundaries, preserve their order and assemble the piles. Read every number from top to bottom: the result should be 1…20 with no gaps or duplicates. This paper model checks the assembly logic; check the printer’s actual output separately.