11.11.2025

Mug cracked in the heat press: how to protect the next one

Mug cracked in the heat press: how to protect the next one

A ceramic sublimation mug most often cracks in the press because the pressure is too high or a heater end presses on the handle; after pressing, the usual cause is cold water. Loosen the pressure until the press lever closes with one hand, centre the mug handle in the gap and let the mug cool in air. If only mugs from one box crack, the batch is the cause.

If a mug cracks in the press, do not wait for the cycle to end. Open the press with heat-resistant gloves and lift the mug out supporting it from below, not by the handle: the handle of a cracked mug can snap off. Stand it on a heat-resistant trivet, then throw it away. Switch the press off, let it cool and inspect the heater: remove any fragments, because even a small chip between heater and mug presses on a single point.

When did you hear the crack?

1
While closing the press
Check the mug diameter, handle position and pressure.
2
During heating
Check the fit and the heater pad; the mug must be sound and at room temperature.
3
After removal
Was the mug dunked in water, covered with a wet towel or set on a cold or wet surface? Cool it in air (below).

Start with a cold fit check

Check the fit on a cold mug heat press, unplugged. The usual setting for a white 330 ml mug is 180–200 °C for 180 s; for a 425 ml mug in the large heater, 200 °C for about 200 s. A thin-walled mug heats up faster: start at 180 °C with lighter pressure. If the product card of your mug gives a different setting, use that. Do not leave a mug clamped in a hot press longer than the cycle, either before printing or after the beep.

  1. Inspect a fresh blank. Use light from the side to check the rim, base, wall and handle joints. Tap the rim lightly with a pencil: a sound mug rings, a cracked one sounds dull. Do not print on a mug with a chip, hairline crack or network of cracks.
  2. Let the mug reach room temperature. Print only on a dry mug. Unpack mugs from a cold delivery and let them stand in a warm room for a few hours; do not make up for a cold mug with a longer time or a higher temperature.
  3. Check shape and diameter. 330 ml mugs come in different diameters. The mug must slide into the heater without force and sit straight. Do not force a tapered blank into a cylindrical attachment.
  4. Recreate the production wrap. Wrap the mug in a sheet of the same sublimation paper and fix it with heat tape, as for printing. The paper must lie without folds: without it, the mug sits looser than during printing.
  5. Keep the handle in the open gap. Centre the mug handle in the gap between the heater ends and close the press slowly. Correct pressure: the press lever closes with one hand and noticeable effort, and the mug cannot turn in the closed press. If you need both hands or your body weight, or a heater end presses on the mug handle, open the press, loosen the pressure screw a quarter turn and check again.

The heater presses the wall; the handle stays clear

Handle centred in the gap

Handle

Heater
Heater

Mug wall

Clearance on both sides

Handle against the edge

Handle

Heater
Heater

Mug wall

Unwanted contact

The handle sits in the gap between the heater ends without touching them.

Do not print if the mug does not slide into the heater without force or the heater pad has dents, cuts or bulges. A standard heater (for example, on the MP160) takes mugs 7.5–9 cm in diameter; a 425 ml mug needs the large heater, a tapered mug the tapered one. Replace a damaged heater: heating elements are among the spare parts. Start every new box with a fit check: the pressure set for the previous box may be too high.

Cold water can ruin an otherwise finished mug

Many people dunk a hot mug straight into cold water to stop the print from blurring. A sound mug with an even wall usually survives this, but a thin-walled mug or one with a hidden hairline crack breaks at exactly this moment: the water chills the surface instantly while the inner wall is still hot. The ceramic contracts unevenly and cracks.

What happens through the wall

Cold water
Outer layer cools quickly
Ceramic deeper inside is still hot

Uneven contraction → stress

Air cooling

↑ ↑ ↑

Dry, heat-resistant surface

Wall cross-section: rapid cooling outside creates a temperature difference within the ceramic.

If mugs crack after water, cool them in air. Take the mug out with heat-resistant gloves, peel the paper at once and stand it on a dry wooden board or trivet; a fan cools it faster. The print will not ghost if the paper is taped tightly at top and bottom with heat tape and you peel it in one motion. If the edges still blur, shorten the press time by 10–15 s.

One trial before the production run

Once the fit is right, print one mug from the same box at the usual setting (180–200 °C, 180 s) and let it air-cool. Keep the design and paper the same.

Cooled intact

Inspect the rim, base and handle. If they are sound, run the order at this pressure.

Cracked again

Take a mug from another box or batch and repeat the trial unchanged. If it survives, the first batch is at fault: set it aside and contact us. If mugs from different batches crack, inspect the heater, especially where the crack starts each time; a dented or cut pad means the heating element needs replacing. No other batch, or no cause found? Contact us as well.

When you contact your manager or technical support, include a photo of the crack, the box markings, the press model, temperature, time and when you heard the crack. Do not deliver a cracked mug to a customer, even if the print is perfect.