24.04.2026

Hot-melt carton flaps: when to join them and when to let go

Hot-melt carton flaps: when to join them and when to let go

When using a packaging hot-melt adhesive suitable for your cardboard, join the flaps while the adhesive can still wet the second surface. Then hold them until the formed joint can stay closed without support. Joining in time and being able to let go are two separate tasks.

First assemble the joint without adhesive: the folds must allow the flaps to meet evenly in the overlap. The board must be clean, dry and free of dust, and the adhesive must suit its surface and coating as well as the working conditions.

Two intervals, one cooling process

Open time is the maximum permitted interval between applying adhesive and joining the parts. During this interval, the adhesive must still be able to wet the second surface: spread over it and establish contact. It is an opportunity to join, not a recommended waiting period.

The adhesive starts cooling during application. Closing the flaps does not restart cooling: it continues after contact as the formed joint sets. A hardened bead on one flap therefore does not mean the two flaps have bonded.

Work sequence, not a time scale

Cooling starts with the first deposited part of the bead and continues after contact

1

Application

The first part of the bead is already on the board. It starts ageing while you apply the rest.

2

Joining

The second flap meets the adhesive while it can still wet that surface. Contact must happen within the open time.

3

Holding → release

Maintain contact without movement. Let go when the joint can keep the flap closed on its own; determine this time separately.

Where the adhesive belongs

In an overlap, the adhesive must contact both surfaces. Joining in time gives it that opportunity, but a skewed flap, an unsuitable coating or incomplete contact can still spoil the joint.

Cross-section through two overlapping flaps; thicknesses enlarged

Outside the box

A
B

Inside the box

A — outer flap

B — inner flap

Adhesive between both surfaces in the overlap

Both flaps overlap at the adhesive bead. This is the area that must be brought together and held without movement.

Four boxes: why the first bead reaches 20 seconds

Hypothetical example: assume that the joining window under the given conditions is 10 s and applying one bead takes 5 s. Both numbers are teaching assumptions, not specifications for a MyPrint adhesive or any other brand. For this calculation, moving between boxes and bringing the flaps together take no extra time.

If you apply adhesive to four boxes in succession and only then close the first, the oldest part of its bead will have waited about 4 × 5 = 20 s. Count from the start of application, not its end. Moving and aligning parts also take time in real work.

Age of the first bead: from its first deposited part to contact

Apply to all four first

Box 1

0–5 s

Box 2

5–10 s

Box 3

10–15 s

Box 4

15–20 s

Each segment is one 5 s application

0–10 s

Assumed window: 0–10 s from the start of the first bead

First joint makes contact only here: ≈20 s

Start of the bead

≈20 s before contact

End of the bead

≈15 s before contact

15 s is the age of the last deposited part, not the greatest adhesive age in this joint. For the first deposited part, 20 s already exceeds the assumed 10 s window.

One prepared joint at a time

5 s application → contact at ≈5 s → hold this joint → next joint

The folds and access to the flap are ready before application. Apply the bead and immediately close that joint. Its oldest part is about 5 s old, within the assumed 10 s window. If the flap still needs adjusting after application, that extra time also counts.

These numbers describe contact timing only. They do not specify release time, strength, readiness for shipping or guaranteed adhesion. Even after prompt contact, the joint still needs the holding time required for that particular joint.

One trial: change only the delay before contact

Compare two identical sample joints made from the same board, with the same coated side facing out. Check the folds and overlap beforehand on both. The aim is to find out whether shortening your usual delay helps.

  1. Keep the adhesive, application amount, location and method, working conditions and temperature the same. Do not change them along with the delay.
  2. Join the first sample after your usual delay and the second immediately after an otherwise identical application. Record the time from the first deposited part to contact, and the holding time after contact, separately.
  3. Keep the pressing action, holding duration and subsequent handling the same for both versions. Compare them after the same elapsed time from contact: does the overlap stay closed, or does the flap lift? Allow the samples to cool before inspection.

If, with the same holding, the promptly joined sample stays closed while the delayed one opens, you have a reason to remove the extra pause from the workflow. This shows the benefit of earlier contact in this trial; a single comparison does not prove that timing was the only cause.

When to let go of the flap

After joining in time, hold the flap in position until the joint can stay closed without your support. Determine the required duration from the specific adhesive data and a trial on your own design. Hold the parts by their outer surfaces without touching hot adhesive.

If the flap lifts after release despite prompt contact, check that the surfaces meet evenly and examine holding. In a separate holding trial, keep the short delay before contact constant and change only the holding time afterwards. Keep the pressing action and all other conditions the same.

Longer holding is not a dependable repair for a bead that set before contact: it does not restore the ability to wet the second surface.

When the stopwatch is not the whole story

Adhesive peeling away cleanly without fibre tear is a clue to investigate the joint, not proof of a missed open time. The board surface, an unsuitable adhesive or incomplete contact can produce a similar appearance. If the board, coating or storage conditions change, check the suitability of the combination separately.

Start with one prepared joint at a time. If even that joint cannot physically be closed within your adhesive’s open time, reconsider the assembly sequence or choose a suitable adhesive with a longer open time under your conditions.