03.07.2025

Heat transfer vinyl lifts with the carrier: what to do

Heat transfer vinyl lifts with the carrier: what to do

If heat transfer vinyl lifts with the carrier, stop pulling and lay the carrier back down. Peel a cold-peel film once the whole area has cooled, and a hot-peel film straight after pressing. If that does not help, re-press for 5–10 s, but do not set the heat press hotter than the film's product page says.

What should stay on the shirt

The clear carrier holds the cut pieces in place. Beneath the coloured vinyl is a heat-activated adhesive: it softens in the press and bonds to the fibres. With a cold-peel film, the adhesive has to cool and set first. Pull too soon and the carrier may lift a letter before it has bonded securely.

Peel off the carrier, the design stays

After pressing, before peeling

Clear carrier with a tacky surface

Separate the carrier here

Coloured vinyl
Heat-activated adhesive
Shirt fabric

After a successful peel

Carrier removed

Remain on the fabric

Coloured vinyl
Heat-activated adhesive
Shirt fabric

The vinyl and adhesive stay on the fabric; the carrier comes off.

When to peel the carrier

The packaging and the film's product page say which. There are three options:

Hot

Immediately after opening the press, while the transfer is still hot.

Warm

After a short cooling period, while the transfer is warm but no longer hot.

Cold

Once the entire transfer area has cooled to roughly room temperature.

For a cold peel, move the garment off the platen onto a flat surface. The centre of a large design cools more slowly than the edges, so check the centre. With a hot-peel film, by contrast, do not wait: peel the carrier straight after pressing in one smooth movement.

Settings and peel timing come from the film's product page

Each film's product page gives its pressing settings and peel timing. Three examples from the MyPrint catalogue:

Polyurethane film, cobalt

150–160 °C · 10–15 s

Medium pressure, cold peel.

White flock

160–165 °C · 25 s

Medium pressure, cold peel.

White PVC film

155–160 °C · 10–15 s

Medium pressure, hot peel.

Polyurethane and PVC film are pressed almost the same way, but the carrier comes off at different times.

How to get the letter to stay down

  1. Stop at the first lifting edge. Lay the carrier and letter back down without moving the design. Do not keep pulling: a fine piece may stretch or tear.
  2. Peel at the right moment. Cold peel: when the centre of the design is no warmer than the fabric next to it; check with the back of your hand, usually a minute or two. Hot peel: straight away. Start at a corner and keep the carrier low, almost parallel to the fabric, while holding the fabric nearby.
  3. Still lifting? Lay the carrier back, cover it with a Teflon sheet and re-press for 5–10 s at the same temperature. This works for polyurethane film, PVC film and flock on cotton, polyester and blends. If there is a seam, collar or zip under the design, put a Teflon pillow under the pressing area so the platen presses evenly. Then peel the carrier again at the right moment.

Do not re-press puff film: it takes only one pressing, and a second one flattens the puff for good. Find its pressure and time on a sample (below), not on a finished garment. Heat will not save a stretched or torn letter: cut and apply a new one.

What did the second attempt show?

Everything stayed on the fabric after cooling
→ Keep peeling the same way. No more heat is needed.
The brief second press worked and the edges are flat
→ The first pressing was not enough. For the next garments, pre-press the fabric for 2–3 s, use the top of the time range on the product page (15 s for polyurethane film) and increase the pressure.
Pieces still lift after the second press
→ Do not heat this garment a third time. Run the square test (below): it shows whether the settings, the press, the fabric or the piece itself is to blame.

Before the next batch

Use a cutting plotter to cut five 2 × 2 cm squares and the same small letter. Take a spare garment from the same batch, pre-press it for 2–3 s to drive out moisture, place the squares in the centre and in the corners of the pressing area, and put the letter where it sits in the design. Transfer them using the settings from the film's product page.

  • All the squares lift — not enough heat or pressure. Use the top of the range on the product page and increase the pressure. If that does not help, repeat the test on plain cotton. If they stick there, the fabric is to blame (water-repellent, softshell, some nylon, silicone finish): ordinary vinyl will not hold on it, so choose a garment without a coating. If they lift on cotton too, the platen probably runs cooler than the display shows: describe the test result to a MyPrint manager.
  • Only the corner squares lift — the platen has cold edges or weak pressure around the perimeter. Place the design closer to the centre and check the press using the article on cold zones and uneven heat press pressure.
  • The squares stick, the letter does not — it was damaged during weeding or is too thin for this vinyl. Cut it again with a thicker stroke and weed while pressing the piece against the carrier.

A clean peel does not mean the design will survive washing. Wash the sample no sooner than 24 hours later and check the edges. Label the roll with its peel method: hot, warm or cold.