If the top sheets of a stack come out shorter than the bottom ones, either the paper shifted under the knife or the blade itself went in at an angle. Most often a dull knife pulls the top sheets out from under a weak clamp, and the taller the stack, the bigger the difference. A pencil line on the side of the stack helps you spot sheets that moved.
Why the top sheets end up shorter
This happens on both manual and electric guillotine paper cutters: the stack sits against the back gauge, the clamp holds it just behind the cutting line, and the knife comes down in front of the clamp.
A sharp knife cuts a sheet through at once, while a dull one first presses it into the stack and drags it along. The top sheets shift most easily: the whole soft stack with its air is below them. If the clamp holds weakly, the blade pulls them out from under it, away from the back gauge. The knife still cuts in the same place, so such a sheet ends up shorter by the amount it moved.
What a dull knife does
1. During the cut
The blade drags the top sheets away from the back gauge.
2. After the cut
The stack is knocked back against the gauge: the top sheets are short by the same gap.
Side view. The shift is exaggerated so that it can be seen.
How to spot sheets that moved
The direction of the taper does not tell you the cause: it can go the other way, with the bottom sheets shorter. Before the next cut, draw a vertical pencil line down the free side of the stack, between the back gauge and the cutting line. Make the cut and, without knocking the stack up, look at the line once the knife is back up; leave the guards in place.
The line on the side of the stack right after the cut
The line is slanted
The sheets moved under the knife: work on the clamp, the stack height and the knife’s sharpness.
The line is vertical, the cut face slanted
The paper right under the knife may still have bent. Start with the same checks below.
The stack has not been knocked up yet. The shift is exaggerated.
What to check first
- Knock the stack up against the back gauge and the side guide to let the air out.
- Put a sheet of card on top: it spreads the pressure and keeps clamp marks off the print.
- Tighten the clamp until the stack cannot shift, and only then bring the knife down.
- Cut lower stacks. The 858 manual guillotines are rated for stacks up to 40 mm: that is how much the knife cuts through in one go, not how much it cuts accurately. Halve the stack and make a test cut. Then lay the top sheet on the bottom one, align the edges that were against the gauge and compare the cut edges.
- If the difference remains, inspect the knife. Signs of a dull knife: the edge is rough and darker than the paper, sheets stick together along the cut, and the handle needs more force. Send such a knife for sharpening or replace it.
If the test cut did not help
If the cut face stays slanted with a sharp knife and a lower stack, have a service engineer check the knife holder, the guides and the knife mounting.
When changing the knife, clean its seat before fitting the new one: dirt or a burr under the blade tilts it out of vertical.
A knife ground at too narrow an angle deflects in dense and coated paper. For paper the bevel is usually ground at 22–24°. When you send the knife for sharpening, ask for the factory angle to be kept.
Top and bottom match, but the cut is skewed
On the piece that stayed against the gauge, measure from the back edge to the cut on the left and on the right. Check the corner with a square.
Different width on the left and right
Repeat the cut with a straight edge knocked firmly against the back gauge. If the difference remains, the gauge is not parallel to the knife: adjust it as the manual describes.
Same width, but the corner is not square
The side guide is not at a right angle to the knife, or the sheet from the pack is not a true rectangle. First set the side guide at 90° to the cutting line, then trim two adjacent edges, check them with a square and place the stack only against them.
Bottom sheet not cut through or torn
Start with the cutting stick and the cut depth; there is a separate article about them.
Treat the first stack of every job as a test: compare the top and bottom sheets, then cut the rest. Spare knives for the 858 guillotines and the My Print electric cutters are in the same section as the cutters.
