If a strip of fabric shows between the fill and outline, check the hooping first. For a small design on a firm canvas tote, use 70 g/m² tear-away embroidery backing and hoop it together with the fabric. Before starting another bag, stitch the same file on a scrap of the same fabric or on a rejected bag.
Why the outline misses the fill
The machine places stitches at the coordinates in the file. As it stitches the fill, the stitches pull the fabric inward; loosely secured fabric can also shift. By the time the machine reaches the outline, the fill edge has moved. This change does not appear on screen.
The fill contracts, leaving a gap
The fill reaches the outline
Fabric shows between the fill and outline
Blue stripes are rows of fill stitches; the dark border is the outline. Stitches pull the fabric along their length, so gaps open at both ends of the rows.
First look at where the fabric shows. If the outline has shifted to one side — a gap on one side, the outline running over the fill on the other — or the fabric has puckered around the design, the fabric moved. Start with the hooping steps below. If the gaps are equal at both ends of the fill stitches and the fabric is flat, the stitches themselves pulled the fill in. Then go straight to the control design in the second table row.
Secure both layers
Backing holds the fabric only when its edges are gripped in the hoop together with the fabric. A piece placed only under the design does not hold it. For a solid dense fill, add a second layer of the same backing; always hoop the first layer.
The hoop must grip the backing
The backing edges are free
Both layers are gripped
Cross-section between opposite sides of the hoop. The backing passes through the grip around the entire perimeter.
- Use the smallest hoop whose sewing area fits the entire design. A 60 × 60 mm design fits a 100 × 100 mm sewing area; a 200 × 200 mm area leaves a lot of free fabric around it, and that fabric bounces under the needle. These are sewing areas, not the frame’s outer dimensions.
- Cut the backing to extend 2–3 cm beyond the hoop on every side. Slide the lower ring with the backing inside the bag under the front panel and lay it on a level table, with the fabric on top facing up. Smooth out folds without stretching.
- Insert the upper ring. If it is too tight, loosen the screw and try again. Run your fingers over the fabric: it should neither slide nor ripple. If it is slack, tighten the screw with the upper ring removed and hoop again instead of tugging the edges through the closed hoop.
- Keep the handles and the back of the bag away from the needle. Attach the frame firmly, without play. Run the design trace on the machine and watch that the bag and hoop do not catch on the table, machine or other objects.
What the repeat sample tells you
Stitch the problem design at the same size, using the same thread, tension and speed. Change only how the layers are secured. Inspect the result in the hoop and after removal. Do not tighten the fabric during stitching: this moves areas already embroidered.
| What you see | Next step |
|---|---|
| The outline meets the fill | Stitch the batch with the same backing and hooping. If the scrap comes out true but the bag shows a gap again, the bag is dragging the hoop: support it so it does not hang, and pin the handles out of the way. |
| The gap remains | On the same fabric and backing, stitch a control design with similar fill and outline: a built-in machine design or one that has already stitched true for you. |
| The control design stitches true | Edit the problem file: compensation, underlay and overlap — values below. |
Pull compensation lengthens the fill stitches so the edge still reaches the outline after the fabric draws in. On firm canvas, start with 0.2–0.3 mm per side. Use edge-run plus tatami underlay laid across the top stitches. The fill should run under a satin outline to about the middle of its width. Do not make the fill denser: the usual row spacing is about 0.4 mm, and a denser fill pulls harder. Edit the stitches in the software; enlarging the whole design on the machine will not help. If you bought the file, send the digitizer a sample photo, the fabric and these values, then stitch another sample after the edit.
If the control design also shifts, check that the frame is attached without play and that the bag catches nowhere, and rethread the upper thread. Then stitch a satin bar and look at the back: the bobbin thread should fill the middle third of its width. More bobbin — loosen the upper thread; less — balance the tension as your machine manual describes. If the tension is right and both designs still shift, show both samples to a service technician: the control design should stitch true, so the frame drive needs checking.
T-shirts and polos need different backing: see choosing backing for woven fabrics and knits.
