Embroidery sticky after water-soluble nonwoven stabilizer, and stiff once dry? Dissolved stabilizer is still in the fabric, and as it dries it stiffens it like starch. Rinse the item in fresh water several times until the fabric no longer feels slippery: the dried residue dissolves again.
Why the sheet is gone but residue remains
In water the stabilizer dissolves but does not disappear: the solution stays between the threads and in the fibres. If you only wet the item and let it dry, it dries right there.
Residue of water-soluble film has to be washed out the same way. Even after the big pieces are off, on a towel its residue sits between the stitches and in the terry loops.
1. Before wetting
Intact stabilizer
The material is still a layer next to the fabric.
2. After wetting
Material in solution
The sheet is gone, but the solution still soaks the fabric.
3. After rinsing
Fresh water → outflow
Water carries the dissolved material away.
The sheet disappears as soon as it is wetted; only rinsing takes the solution out of the fabric.
How to wash out the residue
- Remove the excess dry. Take the item out of the hoop. Trim the loose stabilizer around the embroidery without catching the fabric or thread. Peel loose topping film off with your fingers while holding the stitches: less material means less to wash out.
- Let the material dissolve. Soak the embroidered area right through and wait until the sheet disappears: the 20 °C type in cool water, the 90 °C type in hot water, and only if the item can take it. Spread the item out so water reaches both the face and the back.
- Change the water. Move the item into clean water or rinse it under a gentle stream. Move the fabric gently in the water. Dry it only once the fabric no longer feels slippery between your fingers. A towel or T-shirt is easier to wash on a normal cycle according to its label: the machine rinses several times on its own.
- Check the dry fabric. Blot with a clean towel and dry according to the care rules. Do not judge by the design itself — dense embroidery is always firm — but by the fabric beside the stitches: it should be as soft as where there was no stabilizer.
20 °C or 90 °C: check the label
MyPrint sells two water-soluble stabilizer types: one for 20 °C and one for 90 °C. Both look the same, and both resemble tear-away stabilizer, which does not dissolve in water at all.
20 °C
For cold water · 40 g/m²
Dissolves in cool water. Needs rinsing after it dissolves.
90 °C
For hot water · 30 g/m²
Needs hot water. Does not dissolve in cool water.
The water must not be hotter than the whole item can take: fabric, thread and trims. So for an item with a 40 °C care limit, use the 20 °C type, not the 90 °C one. If the 90 °C type is already stitched into such an item, keep it out of hot water: trim the stabilizer as close to the stitches as you can and leave what is under them.
What to do if residue remains
| What you see or feel | Next step |
|---|---|
| The sheet or pieces did not dissolve | Check the label for the water temperature the stabilizer is rated for. No label? Test an offcut (below). Film marked “heat-away” does not dissolve in water; it is removed with heat. |
| The sheet is gone, the surface is slippery | Keep rinsing in fresh water: what has to go now is the dissolved material. |
| Fabric beside the stitches is stiff after drying | Dried residue dissolves again: soak the item in a large bowl for at least 10 minutes, then rinse until the fabric no longer feels slippery. No change? Identify the stabilizer with the offcut test (below) and check whether spray adhesive was used. |
| Fabric is soft, only the design is hard | That is dense stitching or tear-away backing under it; water will not remove it. |
No label? Drop an offcut of the same stabilizer into a glass of room-temperature water and stir: the 20 °C type starts to soften and break up almost at once. If the offcut is still whole after a few minutes, drop another one into just-boiled water: the 90 °C type dissolves, tear-away does not. Pull tear-away off close to the stitches. Dissolve the 90 °C type in hot water only if the item can take it; otherwise trim it as close to the stitches as you can.
The stabilizer dissolves in water, but temporary spray adhesive does not always: some of these adhesives fade over time or with heat. If it is sticky exactly where the adhesive was, read the can for how to remove it. Next time spray lightly, onto the stabilizer rather than the garment.
Before a batch, take one item all the way — rinse it and let it dry completely — and only then embroider the rest: wet fabric feels soft even with residue in it.
