If the clamp on your guillotine paper cutter leaves a band on business cards, cover the stack with smooth board about 1 mm thick and make a trial cut. The clamp mark then stays on the board, not on the print. Do not loosen the clamp at random: if the stack is held too weakly, the top cards will come out a different size from the bottom ones.
Does the mark appear without moving the knife?
A clamp mark is a band or a row of matching dents along the cut edge, where the clamp held the card. On manual cutters with a screw clamp (tightened with a handle or handwheel), the clamp is lowered separately from the knife, so this is easy to check:
- Raise the knife and lock it. Load a trial stack; the top sheet must be free of marks.
- Clamp it as firmly as you would before a cut, release the clamp and remove the top sheet.
- Look at the sheet in raking light. An even band along the whole clamp means pressure. Separate dots or scratches in the same place mean dirt or a burr on the clamp: wipe its underside with the knife locked, then repeat the test.
On dark matte and laminated cards the clamp often leaves a glossy band rather than a dent. Always cut these cards with board on top.
If there is no mark without the knife, but after the cut you see a rubbed band under the clamp or a crushed edge, the knife or shifting sheets are to blame, not clamp pressure. How to fix that is covered in “Guillotine cuts the stack at a slant”.
On an electric cutter where the clamp only comes down together with the knife when you press both cut buttons, you cannot test it without the knife. Go straight to the comparison trial in “Check both the surface and the size”.
Board on top, under the whole clamp
Use flat, smooth board about 1 mm thick with no creases or dirt, such as the cardboard back of a notepad. Lay one sheet-sized piece on the stack: it must lie under the whole clamp and reach the cut line. Do not piece the board together from scraps: where they overlap, they will leave a mark too. Corrugated board and leather-grain binding covers will not do: their texture will press into the cards.
Where the clamp mark ends up
Direct contact
The clamp presses straight on the print
With protective board
The dents stay on the board
The board lies between the clamp and the top card and is cut together with the stack.
The knife cuts the board together with the stack, so the card size and the narrowest strip stay the same. The board only takes up height: count it within the maximum stack height of your cutter — 40 mm on the manual A4 guillotines in the MyPrint catalogue. Insert or replace the board only when the knife and clamp are up; on a manual cutter, lock the knife as well. Keep the guard in place.
Check both the surface and the size
Cut two identical trial stacks, one without board and one with it. Keep the stock, sheet size and clamping force the same. After cutting, inspect the top card, then place it over the bottom one, aligning the edges that were against the backgauge.
| What you see | What to do |
|---|---|
| No mark; cut edges match | Cut with this board. Replace it as soon as it gets dirty or dented. |
| The band remains; cut edges match | Check that the board lies under the whole clamp and reaches the cut line; replace it if it is dented. On a manual cutter, tighten the clamp only until the stack stops moving, not as hard as you can. Repeat the trial. |
| Top and bottom cards differ in size | If you loosened the clamp, restore the previous force and repeat the trial. If the difference remains, the knife or stack movement is to blame; the article on slanted cuts explains what to do. |
When cutting narrow stacks of business cards, put a pile of offcuts or waste sheets of the same height under the other end of the clamp. The clamp then comes down level instead of pressing into the cards with its edge. Check the first narrow stack with a trial as well.
If the mark remains even with the board and a clean clamp, contact the MyPrint technical department. Tell them the cutter model, the stock (weight, lamination) and the stack height.
