If the upper sheets separate but the bottom ones stay joined, the support beneath the blade also needs checking. On a guillotine paper cutter with a replaceable support strip, this part is called the cutting stick. A worn working track can prevent the cut from finishing. Uncut bottom sheets alone do not prove that the knife is dull or that the stick is the only cause.
The useful result after the machine’s prescribed servicing and setup is complete separation across the full working width, followed by a clean cut through a small stack of the intended material. Rotating or replacing the stick does not, by itself, confirm that result.
What happens beneath the last sheet
At the end of its stroke, the blade must pass through the bottom sheets and reach the support beneath the cutting line. The stick supports the paper in this area and receives the blade’s contact. If the working track already has a worn recess, the last sheet may lack support: paper can deflect into it while some fibres remain intact. This can leave the bottom joined by a paper bridge even though the upper sheets have been cut through.
A complete cut: the blade reaches the support
Simplified cross-section
Blade
Paper stack
Bottom sheet
Cutting stick — replaceable support
The blade passes through the last sheet to the stick. Part sizes and positions are illustrative; this explains contact, not a machine setting.
The support’s working track matters
Usable track
There is a usable supporting surface beneath the blade line.
Worn track
The illustrated recess was already in the support before this cut. It can affect the bottom sheets.
Illustrative surface profiles with no blade or paper shown. Wear depth has not been measured; the appearance of a mark alone does not establish whether the stick is usable.
If the design permits another working track to be used, the stick is rotated or repositioned according to that machine’s instructions. If no usable surface remains, a compatible replacement is needed. The knife and its final position also affect completion of the cut, so a fresh track does not remove the need for the manufacturer’s prescribed setup check.
An uncut centre: what an edge trial cannot show
Hypothetical example: after a cut, the upper sheets separate, but a narrow paper bridge still joins the bottom sheet at its centre. The cut is complete on the left and right. This stack alone cannot tell you whether the cause is the support, an uneven knife or its setup.
Bottom sheet after an incomplete cut
Top view
Left
Centre
Right
Cut through
Uncut bridge
Cut through
The white gaps are sections already cut through. The orange centre is paper that still joins the two parts of the sheet.
A narrow trial on the left only
Separated here
No trial paper here
A successful left-edge trial showed nothing about the centre or right edge: they were not part of this cut.
After servicing, the test paper therefore needs to span the full working width as prescribed by the manufacturer. Assess the whole line, including the centre and both edges: has the bottom sheet separated completely, with no paper bridges? Tearing a bridge apart by hand does not make it a completed cut.
After servicing, check the result
Inspection, rotation or replacement of the stick and checking the knife stroke must be carried out by the person authorised to do so under the particular cutter’s instructions. Servicing requires the specified power isolation and lockouts; test cuts use the machine’s normal safeguards. Inspect the paper outside the danger area while the machine is in the safe state defined by its instructions.
Do not improvise extra depth or force to push through the last sheet. Excessive blade penetration into the stick can dull the knife. A knife that hesitates in the paper, draws sheets or leaves marks on the cut face also needs its condition checked under the machine’s procedure.
What the check showed
Separated across the full width
Next, check a small stack of the paper or card you intend to use, within the cutter’s permitted limits. The bottom sheets must separate completely and the edge must be acceptable.
A paper bridge remains
Checking the support has not yet resolved the problem. Keep the sample and note the uncut location; the support installation, knife stroke and knife condition need checking under the manual or by service personnel.
All sheets separate, but sizes differ
If sheets at the top and bottom have different lengths and the cut face slopes, that is a different defect: cut geometry. Replacing the stick is not an automatic answer to it.
If the stick was serviced and the knife was set up at the same time, and the cut became complete, you only know that the combined work restored the result under the conditions checked. That comparison does not prove the stick or the knife was the sole cause.
A replacement needs the exact model
For example, the PVC cutting stick for the My Print 858 A4 is a spare for the model named in its title. It is not a universal strip for every A4 cutter. Before ordering, check the machine’s full model designation and the part’s compatibility; the paper format alone is insufficient.
Start with the cutter model and a sample of the bottom sheet: note where it remains joined — left, centre or right. That helps arrange the right check. Afterwards, assess the paper across the full width and in a small working stack, rather than just confirming that the new part is installed.
