Do not transfer a banded print onto a product or run a cleaning cycle at random. First, print simple solid color blocks and a nozzle check. If the nozzle check is complete, check the print mode, printhead alignment, paper condition and paper feed. Change only one condition in each new print; otherwise, you will not know what affected the result.
This sequence applies to bands that are already visible on sublimation paper. If the defect is visible only after heat transfer, also check the blank and transfer conditions. Paper that looks even does not by itself exclude a printing cause: compare control samples under unchanged conditions.
First mark the paper-feed direction
Do not describe a band as simply horizontal or vertical: rotate the sheet and the label changes. In a clear area of the finished print, draw an arrow showing the direction in which the paper travelled through the printer. Then describe the defect unambiguously: does the band run across the feed direction or along it?
Direction alone does not identify the cause. Bands across the feed direction may result from either nozzle dropouts or an incorrect paper-feed step. The arrow lets you compare subsequent sheets in the same orientation, even if a photo of the print has been rotated on screen.
- 1Set the defective sheet aside and record the file name, paper type and selected print mode.
- 2Create a test sheet with wide, solid blocks of cyan, magenta, yellow, black and neutral gray. Add a block in the color where the band was most visible.
- 3Print it on the same paper without making any other changes.
- 4After each subsequent attempt, record only one change and its result.
Separate a file defect from a printing defect
If the test blocks are even but the band appears only in the production artwork, check the file first. One even control does not exclude an intermittent printer fault. Open the print file in another application, inspect the affected area at higher magnification and recreate it from the source artwork.
There is a more precise check: move the artwork on the sheet and print it using the same settings. If the band moves with the image, look for the cause in the file or its processing before printing. If it remains in the same place relative to the edges and the feed arrow, move on to the printer and paper.
Record which color blocks show the band, but inspect every channel in the nozzle check. After software processing, a patch color may be produced by a mixture of inks, so that color alone does not identify a faulty channel.
The nozzle check determines whether cleaning is needed
Print the built-in nozzle check as described in the instructions for your exact model. Judge the check lines, not a photo or the customer's artwork.
- ✓DoThere are gaps or faint segments. Run the standard cleaning procedure as instructed by the manufacturer, then print another nozzle check.
- ×Do notAll check lines are complete. Do not run a cleaning cycle. It will not fix the file, printhead alignment, print mode or feed step.
- !CautionThe gaps are not decreasing. Do not exceed the actions that the manufacturer permits an operator to perform on this model.
Cleaning has one clear condition: the nozzle check has gaps. When the check is complete, another cleaning cycle only wastes ink and does not test any of the remaining causes.
If the nozzle check is complete, check the mode and alignment
Keep the same test file and the same paper. First, make sure the settings specify the type of paper you loaded. Then run the following checks separately and in this order:
- 1Instead of the fastest mode, select a mode that prioritizes quality. Print the test blocks and compare the result before changing anything else.
- 2If bands remain and the model instructions permit it, separately turn off printing while the head moves in both directions. Leave the other conditions unchanged.
- 3Print the same test blocks and compare them with the previous sheet, using the feed arrow for orientation.
- 4Use the comparison to retain a mode that produces an even print. If bands remain, check standard alignment following the model instructions as a separate next test.
Do not change the quality setting, paper type, printing in both directions and the file at the same time. If a slower mode improves the print, another cleaning cycle is not the next step. Align the printhead or choose a mode in which the printer works consistently.
Adjust paper feed after checking the nozzles and alignment
The feed step is the distance the printer advances the paper between passes of the printhead. If the paper advances inaccurately, adjacent passes leave a light gap or overlap to form a dark band. On a solid block, this defect repeats across the feed arrow.
Use the printer's standard paper-feed adjustment only when the nozzle check is complete, the printhead is aligned and the correct paper type is selected. Print the feed-check sheet on the same media, load it in the same way and select the mode you will use for production. Choose the result with the smallest gap or overlap, following the printer's on-screen guidance or instructions.
Do not copy a numeric value from another machine or try to replace a feed adjustment by scaling the artwork. If your model has no such adjustment, contact a service center after checking the nozzles, mode, alignment and paper.
Do not adjust the printer on distorted paper
Place a clean sheet on a flat surface. Curled edges, waviness, creases or skew in the guides make the feed check unreliable. Load a flat sheet with the print side correctly oriented, move the guides snugly against it without creasing it and repeat the test print.
Do not change the media type during one check. If you had to use a different paper, treat that as a new condition and repeat the check from the beginning. For later work, you can choose sublimation paper in the required size, but its compatibility and settings must be checked against the specific printer.
What each check result means
| What you see | What it means | Next action |
|---|---|---|
| What you seeThe test blocks are even, and the band moves with the artwork | What it meansThis points toward the file or its processing; verify with another control print before excluding the printer | Next actionCheck the source artwork and create a new print file |
| What you seeSegments of one color are missing from the nozzle check | What it meansNozzle dropouts may still be causing the bands | Next actionRun the cleaning sequence permitted by the manufacturer and repeat the check |
| What you seeThe nozzle check is complete, and slower printing produces a more even result | What it meansThe result points to mode or alignment; it is not a final diagnosis or a reason for unnecessary cleaning | Next actionAlign the printhead and choose a mode that produces an even test print |
| What you seeLight gaps or dark overlaps repeat across the feed direction | What it meansAfter a complete nozzle check, this is a reason to check the feed step | Next actionRun the standard feed adjustment on the production paper |
| What you seeThe bands change with waviness, skew or the edge of the sheet | What it meansThe condition or loading of the paper affects the defect | Next actionFlatten or replace the sheet, load it correctly and restart the comparison |
When to stop and contact a service center
Your own checks end not when you run out of guesses, but when the next action falls outside the operator instructions. Stop if:
- the gaps in the nozzle check do not decrease after the sequence permitted for the model;
- the standard alignment or feed adjustment does not produce a test option without a visible gap or overlap;
- the paper rubs against the printhead, creases or becomes soiled after correct loading, and the user manual provides no permitted way to correct it;
- the next step requires disassembling the printer or using a setting that is absent from the user manual.
Before contacting a service center, prepare a photo of the entire sheet with the feed arrow, a detailed photo of the nozzle check, the printer model, paper and ink names, the selected mode and a brief record of every change. This set shows more than simply “there are bands”: it shows which causes have already been ruled out and after which action the result stopped changing.
After this sequence, one of four decisions remains: fix the file, clean the nozzles as instructed, adjust the mode and alignment, or adjust the feed using stable paper. If none of the branches changes the test print, the next step is a service center—not another cleaning cycle.
