01.07.2025

A white shadow on one side of a DTF print: how to align the layers

A white shadow on one side of a DTF print: how to align the layers

If a white rim shows on only one side of the design, the underbase has most likely shifted relative to the colour. Correct the alignment on your DTF printer, and only then adjust the choke: a large choke hides the rim but removes white beneath fine details.

Look at the printed DTF film from the back, through the film, against a dark background: this is how the design will look on the garment. A solid white edge on one side means the layers are offset, and on the opposite side the colour edge looks duller because there is no white under it. Scattered dots outside the design are a different problem. If the shadow appears in only one design while other jobs print cleanly, the cause is in the file: see the last section.

Choke changes size; alignment changes position

The white ink underbase blocks out the fabric colour. If it shifts to the right, some colour on the left loses its white backing, while white extends beyond the right edge. Choke trims the underbase around its perimeter but does not move it back into place.

What happens to the layers

1. White has shifted

Colour layer

White underbase · Fabric

White protrudes on the right; colour on the left has no underbase.

2. Choke alone

Colour layer

White underbase · Fabric

The rim is hidden, but more colour on the left has lost its white backing.

3. Layers aligned

Colour layer

White underbase · Fabric

White sits beneath the colour, with the same small inset on both sides.

Cross-section of the finished print: shrinking the underbase does not move its centre.

Check the offset with the printer's built-in test

Check with the built-in calibration test, not with your own design. Print in the same mode as the failed job: resolution, speed, uni- or bidirectional printing and head height all change the alignment. That is why an offset often appears after a head replacement or a change of print mode or head height.

  1. Save the settings and check the nozzles. Take a screenshot of the current values. If the nozzle check has gaps or bent lines, clean the head first: an incomplete pattern cannot give a reliable alignment. Inspect the white nozzle check against a dark background.
  2. Print the calibration tests in order. They are in the printer control software, not in the print preparation software. Start with the feed step: it sets the alignment along the film. Then white-to-colour alignment: on a printer with two or more heads this is head spacing, horizontal and vertical; on a single-head printer it is channel alignment. Finish with bidirectional alignment. Print on the same film. Before removing the test, mark the feed direction in a blank area.
  3. Find the pair of lines that match most precisely. Examine the test with a magnifier or a phone camera. Enter the number of that pair as the correction. If the field only takes the full value, add the number to the current value.
  4. Repeat the test. The best match should now be at the zero mark. If it is not, restore the saved values and repeat step 3. Some printers have separate tests for leftward and rightward carriage travel; check both. Then print the failed design again: the white edge should be gone.

Identify the offset relative to the film

What the test showsWhat to calibrate
Offset along the film feedFeed step, then vertical head spacing.
Offset across the filmHorizontal head spacing; on a single head, channel alignment.
Doubled or fuzzy edges on the test lines themselvesBidirectional alignment. If the rim disappears in unidirectional mode, this is the cause.

Judge direction by the way the film moves through the printer, even if the design is rotated.

If the offset is different every time, new corrections will not help. Check that the film is loaded straight, the pinch rollers press evenly and the roll is not pulling. If that does not help, send service photos of three consecutive tests and the current values. Do not loosen the head mounting: white and colour are aligned in software, and a technician sets the heads mechanically.

When the white underbase does need more choke

A thin, even rim remains all around the outline after alignment? White ink spreads slightly more than colour, so a small choke is normal. Set it in your print preparation software: usually 2–3 pixels, up to 5 on black fabric. Add one pixel at a time and keep the smallest value that removes the rim while small text and fine lines still have white beneath them. If the rim remains even at 5 pixels, go back to alignment instead of increasing the choke. Less white ink will not correct an offset.

How much white does choke remove?

Colour line: 1.0 mm

White beneath it: 0.6 mm

1.0 − 0.2 − 0.2 = 0.6 mm

A 0.2 mm choke on each side: a 1 mm line keeps 0.6 mm of white, a 0.4 mm line keeps none.

The test is aligned, but your design still has a shadow?

Then the cause is in the file. Open the white-layer preview in your print preparation software. If the white is shifted or larger than the colour (it was drawn by hand as a separate layer), align it or let the software generate the white automatically. A soft shadow or glow in the artwork also gives a pale “shadow” on one side, because the software prints white under semi-transparent pixels. Remove such effects or replace them with solid colour.

After the correction, use a heat press to apply one sample to the job's fabric. Inspect the edge, small text and fine lines. Pressing again will not remove the offset: white and colour transfer together. Reprint such a transfer for dark fabric; on white fabric the rim does not show, so it can still be used there. Save the successful print mode for subsequent jobs.