24.04.2025

A step after corner rounding: what to check

A step after corner rounding: what to check

If a corner rounder leaves a step on the card, first check that the blank has a square corner and sits against both guides. Then round a few cards one at a time, and move on to a stack only when the corner comes out clean every time. If the step appeared right after a blade change, start with the guides.

The curve should blend into both edges

A step is a shoulder or notch where the curve meets a straight edge. Even a sharp blade leaves one if the card has shifted or the guides are not set for this blade. The blade sets the shape of the curve; the guides set where it runs. If the card did not reach a guide, the curve runs into the edge at an angle. If a guide is not set for the blade, the edge juts out past the end of the curve, as in the diagram.

Smooth transition

The curve blends into both edges

A step

A break where curve and edge meet

Enlarged corner outlines after cutting. Orange marks the step.

Start with the blank and both guides

Take three fresh blanks of the same material.

When clearing scraps or adjusting the guides, keep your hand off the lever and remove scraps from under the blade with a brush, not your fingers. Switch off and unplug an electric machine first. During the cut, keep your fingers well away from the blade and the pressure foot.

  1. Check with a square. Place the square against the corner of the blank: both edges must sit flush with no gap. If the corner is out of square, trim the blanks on a paper cutter first.
  2. Press against both guides. First brush away scraps near the guides. Both adjacent edges must touch their guides at the same time. If there is a gap, remove the card and position it again.
  3. Cut each card separately. Before cutting, pencil-mark the edge that will sit against the left guide. Hold the card still and push the lever all the way down.

Two contacts

90°

Both edges touch their guides

One contact

90°

Contact below; a gap on the left

Seating before the cut, viewed from above. Blue lines are the guides.

What the three individual cards show

ResultNext action
All three corners are cleanMove on to a small stack, jogging it square on the table first. If the step appears only in the stack, make the stack smaller and check that the clamp holds: small cards creep away from the guides under the blade.
The step is always at the same guideThe guide next to the step does not match the blade. This happens after a blade change or when a guide has shifted during work. Check that the blade is fully seated and set the guide for its radius; if the guide has radius marks, set it to the mark of the fitted blade. Do not bend a fixed guide; show the trial cards to a service technician.
The step changes side or sizeThe card sometimes stops short of a guide and sometimes shifts under the blade. Press it against both guides the same way every time and repeat the test.
The curved edge is fuzzy or tornThe blade is at fault here, not the seating. Check that the blade is fully seated and has no nicks. Replace a dull blade on a desktop rounder with a set of the same radius, upper and lower together.

If the edge juts out past the end of the curve, move the guide next to the step a fraction of a millimetre towards the card; if the curve runs into the edge at an angle, move it away. Test again after every adjustment.

Can the cut cards be saved?

Fix the cause first, then try on one card. Round the same corner again with the card pressed firmly against both guides: if paper was left at the junction and the curve runs into the edge at an angle, the blade trims it off, and the size and radius stay the same.

If the paper beside the curve is already cut away and the edge juts out past the end of the curve, as in the first diagram, another stroke will not help. Round all four corners with a larger-radius blade, for example R10 instead of R6 (the desktop RC01 comes with both blades): the larger curve cuts the step away and the card keeps its size. After changing the blade, set the guides for the new radius. If corners must match across the batch, redo the rest of the cards the same way.

If a larger radius does not suit the design, trim the card to a smaller size on a paper cutter and round it again, provided the margins around the print allow it. Otherwise make new blanks. Keep one clean sample to compare with later corners.