12.09.2026

44 mm badge, 54 mm insert: what wraps around the edge

44 mm badge, 54 mm insert: what wraps around the edge

Cutting a 44 mm paper circle just because the badge is called “44 mm” can remove the material that needs to wrap around the edge. The MyPrint pc44 cutter specifies a 54 mm diameter insert. Use that dimension for the outer artwork circle and the sheet calculation.

Two circles, two different roles

Workshoptogether

Schematic, not a print template. The circles show the 54:44 ratio; their size on screen is not a physical reference.

54 mm · cut line

The outer boundary of the paper insert. Extend the background to it all the way around.

44 mm · nominal guide

A guide based on the nominal badge size. It is neither a measured boundary of the flat visible face nor a guaranteed safe text circle.

(54 − 44) / 2 = 5 mm

The radial difference between the two circles in the artwork. It does not define a guaranteed text clearance.

Where the outer part of the paper goes

front face

→ ←

the edge folds towards the back

Simplified cross-section: the teal line is paper carrying the background; the grey line is the support beneath it. Thickness and shape are schematic.

The paper curves around the shell edge, and its outer portion is folded into the back. Artwork that ends at the inner circle can therefore leave white paper on the curved edge. Do not automatically apply the same 54 mm dimension to another 44 mm badge system: it needs its own specified insert diameter.

Background to the cut, key content towards the centre

Set the artwork circle to 54 mm wide and 54 mm high. Add a centred 44 mm guide that will not print. Extend the background colour or image through the outer ring; move names, faces and essential logo strokes inwards from the nominal guide.

Background stops too soon

Name

The white ring is unprinted paper: it may appear on the curved edge.

Background reaches the cut

Name

The background continues outwards; key content stays near the centre.

Illustrative artwork comparison, not photographs of finished badges. The dashed line is the 44 mm guide; the text position is an example.

Before printing, remove the 44 mm guide from the printed image. Use the first assembled badge to check that the full wording reads from the front, key details do not slip onto the curve, and the background covers the edge. If the composition does not work, move or reduce its important elements while keeping the insert diameter at 54 mm.

54 mm in the file must stay 54 mm on paper

Set the document to the chosen sheet size and print the PDF without fitting it to the page: use actual size, 100%. Automatic fitting can change the scale. Printing without scaling can also crop anything outside the printable area, so place the layout inside that area first.

On a trial sheet, place two reference lines outside the circles: one horizontal and one vertical, for example 50 mm each. Use a ruler to measure both lines and the printed circle diameter in both directions.

A proportional reduction example

In the filereference line
50 mm

insert circle → 54 mm

On paperreference line
47.5 mm

insert circle → 51.3 mm

47.5 / 50 = 51.3 / 54 = 0.95

Both dimensions are 95% of their intended size.

The numbers are chosen for explanation. The diagram lines show a proportion, not physical size on screen.

If both reference lines and the circle change by the same proportion, first check the shared scaling on the path to the print: export settings, the printing application and the driver. The measurement gives a direction for investigation, but does not identify one specific printer fault. Correct the fitting setting and repeat the reference print; do not redraw the circle larger to compensate for 95% output.

If both lines have the intended length but the circle does not, check the object's own dimensions and its geometry in the exported PDF. If the horizontal and vertical measurements have different scale factors, a single proportional reduction does not explain them: compare width and height separately in the document, PDF and print.

A4: calculate with the 54 mm insert

Take a specific rectangular grid example. The margins and gaps below are chosen calculation inputs, not cutter requirements or a specification of your printer.

A4 sheet: 210 × 297 mm. Margins: 10 mm on every edge. Gaps between circles: 2 mm. Each insert: 54 mm diameter.

210 mm

123
456
789
101112
55 mm below the grid

A4 · 297 mm high

10 mm margin · 190 × 277 mm available

166 × 222 mm grid

Proportional sheet schematic: the dashed boundary is the available rectangle; the teal circles are 12 inserts. Labels and numbers are not printed in the production artwork.

After margins

210 − 2 × 10 = 190 mm297 − 2 × 10 = 277 mm

3 columns

3 × 54 + 2 × 2 = 166 mm

Four need 222 mm, exceeding the available 190 mm.

4 rows

4 × 54 + 3 × 2 = 222 mm

Five need 5 × 54 + 4 × 2 = 278 mm. Only 277 mm is available: 1 mm short.

Why the fifth row does not fit

Space after 4 rows: 277 − 222 = 55 mm

One more row and gap: 54 + 2 = 56 mm

It needs 1 mm more. Do not shrink the insert to hide this difference.

3 × 4 = 12 inserts under this example's assumptions

This is the result for the stated rectangular layout, not the maximum A4 capacity or a search for the tightest circle packing. Different margins, gaps or arrangements need a new calculation.

100 inserts → 9 sheets, plus allowance for setup and spoilage

8 × 12 = 96; the ninth sheet needs another 4 inserts.

Round 100 / 12 up to 9. This sheet count excludes extra allowance for setup and spoilage; plan that separately for your process.

Before printing the rest of the order, use the first sheet to check scale and whether the cutter can reach every circle. If it cannot reach the inner positions, change the arrangement or plan to cut the sheet into strips the tool can accept, keeping each insert intact. The first assembled badge confirms the composition; then you can repeat the checked layout.