Support for a 125 µm pouch does not mean you can laminate any card inside it. Check the permitted film and the material thickness separately, using the layers specified in the manual's definition. If the limit includes the pouch, add both pouch sides to the paper thickness.
Does 125 µm mean one side or both?
When choosing film for hot lamination, check the explanation of thickness on the packaging as well as the format. This category also contains rolls and materials for cold lamination; the discussion below concerns hot laminating pouches with two sides enclosing a paper insert.
Look for a definition such as “per side” or “combined thickness of both sides”. If 125 µm is specified per side, the two pouch sides contribute 250 µm before you add any paper. If the number already covers both sides together, do not double it again. Ask the manufacturer or seller to clarify an ambiguous marking before choosing the pouch.
1 µm = 0.001 mm. So 125 µm = 0.125 mm, and two such sides add up to 0.25 mm.
The calculation needs the thickness of your actual paper
The unit g/m² describes mass per area, not thickness. A label of 250 g/m² does not mean 250 µm: papers with the same mass per area can have different thicknesses. Find the thickness, also called caliper, in the specifications for that exact material, or measure the prepared insert with a suitable instrument, such as a micrometer.
For thin paper, you can measure a neatly aligned stack of identical sheets and divide the result by the sheet count. This is an approximation. Account for instrument error: if it could change your decision near the limit, obtain a more precise thickness or choose a thinner combination.
What does the manual mean by “material thickness”?
The film range and maximum material thickness are separate specifications. For the film, check the units and how the sides are counted. For the material, find the exact definition: the insert alone, or the insert together with the pouch. A limit that says “including the pouch” is compared with the sum of all three layers.
The phrase “maximum document thickness” alone, without a definition of the layers included, does not establish a full-stack limit. If it refers only to the insert, compare the insert alone with it. If the permitted combination remains unclear, ask the machine manufacturer: “What is the maximum material thickness including both pouch sides?” The inlet slot width does not establish this.
The film is permitted, but the complete stack is too thick
A hypothetical card example: the insert is 0.30 mm thick, and each complete pouch side is 125 µm. Suppose the machine permits 125 µm per side and a maximum material thickness of 0.50 mm including the pouch. These are teaching assumptions, not specifications for a particular product or laminator.
Three layers where the paper sits
Top pouch side
Film together with its adhesive layer
0.125 mm
125 µm per side
Paper insert
Thickness of the actual insert
0.30 mm
Bottom pouch side
Film together with its adhesive layer
0.125 mm
125 µm per side
Total including the pouch
0.55 mm
0.125 + 0.30 + 0.125 = 0.55 mm
Schematic cross-section; layer thicknesses are exaggerated. Here, 125 µm already covers the complete side including adhesive, so adhesive is not added again.
Two independent checks
Film thickness
125 ≤ 125 µm
Per side: the chosen film and the permitted value use the same definition.
The film thickness condition is met
Material including the pouch
0.55 > 0.50 mm
The insert is added to both pouch sides.
The total thickness limit is exceeded
Hypothetical limit: 0.50 mm
Excess: 0.05 mm
The vertical mark on the bar indicates the limit. The short section to its right is the excess thickness.
Do not feed this combination into the laminator or try to force it through. The permitted 125 µm per side does not override the separate 0.50 mm limit including the pouch.
What to change in this card
With the same hypothetical 0.50 mm limit, you could reduce the insert thickness or choose a thinner pouch that the machine also supports.
Thinner paper, the same pouch
0.20 mm insert; 125 µm pouch per side
0.125 + 0.20 + 0.125 = 0.45 mm
0.45 mm
Below 0.50 mm
A thinner permitted pouch, the same paper
0.30 mm insert; 80 µm pouch per side
0.08 + 0.30 + 0.08 = 0.46 mm
0.46 mm
Below 0.50 mm
Both totals meet the stated overall thickness limit; the 80 µm option is suitable only if the machine permits that pouch. This checks thickness. The suitability of the paper and film for hot lamination, the permitted operating mode and the stiffness required for the finished card remain separate conditions of the choice.
Write down three values before a trial
- Pouch thickness, with its definition: per side or combined for both sides.
- The thickness of the actual insert in µm or mm, not its g/m².
- Both machine limits: for film and for material, with an exact list of the layers included.
Compare quantities that use the same definition. If either condition fails, change the card's materials or the equipment. Once the thickness and materials are permitted, make a trial piece with the same insert, using the mode specified for the selected pouch and machine. Assess the bond and stiffness before making the remaining cards.
